Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Stainless Steel Standoff 1.25" Base 1/4" x 20 Thread .75" Tall - 6-PackUnlike the SOB standoffs which have a blind thread, the SOT series standoffshave a thread which runs all the way through the barrel of the standoff.This allows the standoff to be mounted from either side of the base. Theseparts are manufactured in 316 stainless steel making them suitable for deckapplications. This standoff is inertial (friction) welded to the baseyielding a very strong part. The bases are all 1.25" in diameter. Use forthrough deck mounting of hardware or anywhere you need a fixed femalethread.

Read more less

.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a .75" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Read more less

No Slide Metal/Composite BonderRevolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.Features: Revolutionary Adhesive Parts Stay Where Placed Without Sliding For Use Overhead and on Vertical Surfaces No Need for Fixtures Quick Guide (pdf)Owner's Manual (pdf)

Read more less

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 10

Read more less

No Slide Metal/Composite Bonder *Case of 10*Revolutionary Metal Bonder will hold heavy parts at application without sliding on a vertical or overhead surface. AT-8040 will hold 3,500 lbs in 40 minutes - no Welding, Drilling, or Tapping.Weld Mount AT-8040 is a solvent-free, VOC Compliant, two-part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, and composites to metals or various substrate combinations. It has excellent adhesion to as-received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steel. AT-8040 forms tough, high-strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.Features: Revolutionary Adhesive Parts Stay Where Placed Without Sliding For Use Overhead and on Vertical Surfaces No Need for Fixtures Case of 10 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.

Read more less

1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.25" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges (sold separately) When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

Read more less

AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 50

Read more less

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and not for bonding to metal substrates. Unlike other 2 part acrylic adhesives AT-4020 has a one year shelf life when stored at 72 degrees but is best refrigerated when ever possible. It is packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.** AT 850 Mixing Tips sku 56273 required ** Brochure (pdf)

Read more less

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Plastic Suction Cup HandleInjection Molded Nylon/Nitrile-Buna Rubber Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat bottoms while swimming or from a dinghy. Attach to your paddleboard or kayak for an extra handle during transport. For use above or below the waterline. Constructed of non-corrosive injection molded nylon and Nitrile-Buna rubber. Designed to assist grip not to leverage full body weight. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Add-A-Snap - Black - 2-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and not for bonding to metal substrates. Unlike other 2 part acrylic adhesives AT-4020 has a one year shelf life when stored at 72 degrees but is best refrigerated when ever possible. It is packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts. Brochure (pdf)

Read more less

Portable Rope Cutting GunPanther’s portable Rope Cutting Gun is ideal for boat, camper and home use. Lightweight (1.5 lbs), the handle fits in the palm of your hand with easy finger pull operation. It makes quick clean cuts in all types of synthetic ropes, lines and strapping. Comes with a generous 4 ft. cord. Operates on 120V AC power. Replacement blades available.Features: Cord length: 4' Operates on 120V AC power Lightweight, durable Ideal for boat, camper and home use

Read more less

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

J1939 Doctor Diagnostic ToolSelf-contained J1939 diagnostics tool with physical network and data analysis on your phone, tablet, PC, or MAC.The J1939 protocol is increasingly being adopted in marine applications, providing monitoring and control for engines, propulsion systems, generators, and electrical networks. To support this trend, a self-contained J1939 diagnostics tool has been developed, featuring a built-in web interface that allows any device with a browser to connect and analyze data seamlessly. With wireless connectivity to mobile devices, users can access critical information from anywhere on the vessel without the need for physical connections.This diagnostic tool not only monitors the J1939 network but also checks its physical characteristics, including voltages, bus load, and frame errors. Users can view all devices connected to the network and drill down into specific data for detailed analysis. Its flexibility is enhanced by an M12 connector, which supports a wide variety of third-party patch cables and breakouts, making it compatible with diverse setups.Easily monitor and manage device fault codes with our user-friendly interface. Click the Fault (Red Cross) icon to view active and historical codes in a clear pop-up. The DM1 Table displays the currently active fault codes, while the DM2 Table provides a record of historical faults.If a fault condition remains active after clearing, the system automatically detects and displays it again during the next PGN transmission, ensuring you always have accurate, up-to-date diagnostic information at your fingertips.For more in-depth analysis, you can also view detailed information for a specific PGN by clicking the Info icon located at the end of that PGN’s row. This will open a pop-up window displaying all relevant data for precise monitoring and troubleshooting.Powering the tool is equally versatile. It can draw power directly from the J1939 network (12/24V) or operate from a separate DC supply through the breakout connection. To support reporting and documentation, the tool allows users to print detailed network reports directly from the browser, just as they would with any standard document, simplifying record-keeping and diagnostics.OperationYou can configure the J1939 Doctor through its own simple web interface. Just open your web browser, enter the J1939 Doctor’s IP address, and you can access the J1939 Doctor web interface. So, no complicated programming software or app required.Through the web interface, you can analyse all the equipment connected to the network and get additional information about the equipment. You can also display all of the PGNs being received.The health section gives you an overview of the network (supply voltage, bus capacity, etc.).Features: J1939 is increasingly used on boats for engine, propulsion, generator, and electrical monitoring Self-contained J1939 diagnostics tool with built-in web interface, allowing any device with a browser to connect and analyse data Wireless connectivity to the mobile device Checks physical characteristics of the J1939 network, such as voltages, bus load, and frame errors Allows viewing of devices and data on the J1939 network Drill down on data for analysis Fitted with an M12 connector from which a wide variety of 3rd party patch cables and breakouts can be connected Can operate from J1939 network power (12/24v) or from a separate DC supply via breakout Print reports of the network via the browser, just as you would any document Specifications:Dimensions: 105 x 72 x 32mmWhat's In The Box? 1m drop cable with male M12 Device Net connector WiFi antenna built-in Owner's Manual (pdf)

Read more less

1.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Read more less

LED Battery TesterSpecifically for all 12 Volt DC batteries.

Read more less

1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

1" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Read more less

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Read more less

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to welding in many applications.The AT-6031 uses AT-651 mixing tips and comes in a 50mL cartridge. Compared to the previous version, users get 13mL more product at the same price.*AT-6031 has a 6-month shelf life and should always be stored refrigeratedFeatures:The nozzle on the cartridge will never freeze up

Read more less

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Read more less

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

8040 Acrylic Adhesive with Plunger AT-8040 is a good general-purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6-minute working time and develops working strength in 40 minutes. AT-8040 has a 12-month shelf life when stored at 72°. Weld Mount recommends that wherever possible this adhesive be refrigerated. Packaged in a 30ml cartridge this adhesive does not require the adhesive gun or mixing tips. The 30ml cartridge will bond 30-50 parts. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. This package contains 10 mixing tips.Features:10 to 1 adhesive

Read more less

Aluminum Wire TieUsed with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc.

Read more less

Spanner Wrench/Deck Plate Key Features:Cast bronze with stainless steel pins to fit 1/4" and 5/16" holes.  Opens to service deck plates or strainer caps with key holes up to 7" apart.  Hangs conveniently near the strainer(s) location.   C83600 bronze

Read more less

Add-A-Snap - Black - 1-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

AT-3 Small White Nylon Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

NAVDoctor NMEA Network Diagnostic ToolNAVDoctor is the perfect NMEA 2000 diagnostic tool for dealers, installers, and boat builders. It turns any mobile device into an NMEA 2000 network analyzer, creating simple and clear web pages that show the health and status of your NMEA 2000 network. NAVDoctor is a portable NMEA 2000 network diagnostic tool/tester. It allows you to quickly check and diagnose the NMEA 2000 network. It combines the functionality of existing NMEA 2000 display programs and test equipment into a single, cost-effective, simple plug ‘n play box.It’s self-powered from the network and creates a local wifi point for a mobile phone, tablet, or PC to connect.  Once connected, you simply access functions through a web browser so there’s no complicated software to install.NMEA 2000 networks are based on a robust Canbus architecture, but one bad device, cable, or termination can have a detrimental effect on performance.  Fault finding can be time-consuming and tricky, so having a NAVDoctor in your toolkit will save you time, money, and frustration.NAVDoctor is an essential tool for every marine electronics technician or installer and also offers the capability of printing a network health check certificate to validate an installation and improve customer service.OperationYou can configure the NavDoctor through its simple web interface, just open your web browser, enter the NavDoctor’s IP address and you can access the NavDoctor web interface. So no complicated programming software or app is required.Through the web interface, you can analyze all the equipment connected to the NMEA 2000 network and get additional information about the equipment. You can also display all the NMEA 2000 data (PGN) being received.The health section gives you an overview of the NMEA 2000 network (voltage, bus capacity, etc.). Finally, the test report section analyses all the NMEA 2000 network, equipment, and data and can generate a PDF.Features: NMEA 2000 Wireless Diagnostic Tool Self-powered from NMEA 2000 bus – fits in seconds Creates its wireless network on the boat or can join an existing network in the workshop No apps are required, NAVDoctor’s simple web interface displays in your browser Lists all devices on the NMEA network and all PGNs being transmitted The health page gives you an immediate snapshot of the network key performance parameters Can log all data to text file for in-depth analysis Generates a Network Health Report that you can either print or save to PDF You can give a health report to the customer or you can retain it for your installation records Specifications:Dimensions: 180mm x 145mm x 40mmWhat's In The Box? 1M NMEA2000 drop cable WiFi antenna built-in Owner's Manual (pdf)

Read more less

Add-A-Snap - Black - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Prop Master Propeller WrenchThe Prop Master™ is the original molded propeller wrench.This 1-1/16" six point socket style prop wrench is made of high tensile strength, indestructible nylon. It is totally resistant to fuel, sun, salt water, and other chemicals. The Prop Master™ is less expensive than metal wrenches which rattle and can cause damage to your boat. However, it has plenty of brawn to get the job done. The Prop Master™ will tighten all 1 1/16" propeller nuts without slipping or stripping. (OMC, Johnson and Evinrude, - over 40 HP, Mercury - over 50 HP) High visibility color makes it easy to locate in dark boat compartments. The Prop Master™ also has a 9/16" garboard drain plug socket on the reverse side. Will not corrode in the salt water environment.Features: Fits All 1-1/16” Prop Nuts (40hp & up) Rugged Nylon Resists Stripping 9/16” Garboard Drain Socket on Back Non-Corrosive in Salt Environment High Visibility Yellow makes wrench easy to find WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Pitch: N/A Material: Polymer Diameter (Inches): 0.6875 Box Dimensions: 2"H x 6"W x 16"L WT: 0.6 lbs UPC: 733572020007

Read more less

Oetiker Stepless Clamp Kit with PliersStepless™ 150-Piece Clamp Rigging Kit by T-H Marine®. This product is made of high-quality materials to serve you for years to come. Designed using state-of-the-art technology and with customers in mind, this product by T-H Marine® will last a lifetime. Features: Plastic storage case contains 150 stainless steel Oetiker earless clamps, 10 each of 15 popular sizes, plus standard pincer installation tool Oetiker hose clamps with mechanical interlock allows use of pre-coated materials Specially formed strip edges reduce the risk of damage to the part being clamped with uniform compression and increased clamping force All 304 stainless steel bands - Kit includes full size range for all marine hose Includes: (10) 5.8-7MM Ear Clamps (10) 7.8 9.5MM Ear Clamps (10) 8.8-10.5MM Ear Clamps (10) 9.6-11.3MM Ear Clamps (10) 11.5-14MM Ear Clamps (10) 12-14.5MM Ear Clamps (10) 13.2-15.7MM Ear Clamps (10) 14.5-17MM Ear Clamps (10) 15.3-18.5MM Ear Clamps (10) 17.8-21MM Ear Clamps (10) 22.4-25.6 Ear Clamps (10) 26.9-30.1MM Ear Clamps (10) 28.4-31.6MM Ear Clamps (10) 37.8-41MM Ear Clamps (1) Oetiker Jaw Pliers (1) Plastic Tackle Tray

Read more less

Stainless Steel Bottle Opener with Brushed Finish Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Thru-Hull Installation Tool Thru Hull Installation ToolThe Concept:THT-530 makes the installation of standard GROCO thru-hull fittings possible by a single installer.  Slide the thru-hull fitting, flanged end first, over the tool.  (It will stop at the proper step.)  Tie a length of monofilament to the eye and place it into the already-cut hole in the hull of the boat.  Apply caulking to the flange of the fitting, and pull the fitting through the hole and against the hull from inside the boat.  Thread the mono-filament through the locknut or seacock. With the fitting pulled firmly against the hull the locknut or the seacock may be screwed onto the fitting.THT-530 fits GROCO Thru-hull Fitting Sizes from 1/2" through 3"

Read more less

Add-A-Snap - White - 1-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less