EEL Pigtail AdaptersThese adapters are equipped with sealing collars and are for use in wet locations.Boat SideFemale Connector: Attaches to boat inlet or cordset30A-125V Locking w/ Sealing Collar SystemDock SideMale Plug: Attaches to dockside receptacle or cordset50A-125/250V LockingWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Pigtail Adapter Box Dimensions: 3"H x 9"W x 11"L WT: 3.2 lbs UPC: 093344051814 Owner's Manual (pdf)

Read more less

CAN Cable - 73681SNetwork connection cableLength: 7M (22.9') Quick Guide (pdf)Brochure (pdf)

Read more less

Shift Knob - 1-7/8" - Smooth Stainless Steel Finish Features: 316 Cast Stainless Steel 1-7/8" Shift Control Knobs Fit Hynautic D-Dec/Sturdy Controls Meets ABYC Specifications

Read more less

Flush Mount Hose AdapterPerfect solution to remove that unsightly hose bib deck fitting and rusty knob. This will enable you to connect your water hose in seconds.Enables you to quick-connect your water hose in seconds. Position this fitting close to your anchor windlass to clean muddy anchors, or locate one on each side of your vessel to make cleanups much easier. Combine the deck washdown fitting with a hose coil washdown hose and keep the deck clutter free.Features: Extra 3/4" GHT male hose adaptor suitable for HoseCoil Water flow available with an easy twist of the fitting Easy to install Position this fitting close to your anchor windlass to clean those muddy anchors. Or locate one on each side of your vessel to make those cleanups much easier Just combine the Quick Release Deck Washdown fitting with a Hose Coil Washdown hose and a high volume Jabsco PAR-Max 4 Washdown pump to keep the deck clutter free Comes with a pre-installed check valve that connects your hose with a simple twist to the deck fitting, even under full pressure Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 8"W x 8"L WT: 0.3 lbs UPC: 671880550253

Read more less

Premium Buffing BrushesTurn Your Buffer Into A Power Brush6-1/2" Soft Brush - Yellow PolystyreneSplit end fibers for safe use on most surfaces Specifications: Type: Tools & Accessories Box Dimensions: 3"H x 5"W x 5"L WT: 0.5 lbs UPC: 703485120781

Read more less

Premium Buffing BrushesTurn Your Buffer Into A Power Brush6-1/2" Stiff Brush - White PolypropyleneMost abrasive brush available. Specifications: Type: Tools & Accessories Box Dimensions: 5"H x 5"W x 6"L WT: 0.5 lbs UPC: 703485120767

Read more less

Premium Buffing BrushesTurn Your Buffer Into A Power Brush6-1/2" Medium Brush - Yellow PolystyreneModerately abrasive brush. Specifications: Type: Tools & Accessories Box Dimensions: 3"H x 5"W x 5"L WT: 0.6 lbs UPC: 703485120774

Read more less

V-Throttle - 42018 H - for 0-5V interfaces (voltage)Throttle with analog voltage interfaceRedundant voltage input, IVS, PWM output.They supply the throttle electronic signal. Required for use with direct connection to electronic throttle on the engine.IP protection: IP65Dim.: 205mm x 110mm (8" x 4.3") Quick Guide (pdf)Brochure (pdf)

Read more less

Main Power Supply Cable - 42053KMain power supply of the systemOne each batteryLength: 3M (9.8') Quick Guide (pdf)Brochure (pdf)

Read more less

Shift Unit - 42023 AIt controls up to 2 shifts with solenoids. Required for use with direct connection to the electrical shift unit on the transmission.IP protection: IP65Dim.: 210mm x 120mm (8.3" x 4.7") Quick Guide (pdf)Brochure (pdf)

Read more less

Shift Cable - 42060 GSolenoid connection cableOne each solenoid shiftLength: 1M (3.3') Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Single Engine w/out TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with: CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Single Engine w/TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with:= CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Twin Engines w/TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with: CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Mini Compact Single Hidden Horn - 12V Features: 304 Stainless Steel Trumpets, Diaphragm, and Mounting Brackets Meets ABYCA-23 for boats up to 12 meters Pre-wired Fits existing hole patterns Much louder than competitive models Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 db@ 1 Meter Specifications: Voltage - Input Range (Volts): 12v Box Dimensions: 2"H x 5"W x 8"L WT: 0.7 lbs UPC: 768170110317

Read more less

All-Stainless Mini Compact Single Hidden Horn - 12V Features: All Stainless Steel Inside & Out 304 Stainless Steel inside and out including a sealed sound unit No rust Guaranteed for 5 years. All meet ABYC A-23 for boats up to 12 meters Pre-wired Fits existing hole patterns Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 dB @ 1 Meter Specifications: Voltage - Input Range (Volts): 12v Color: Stainless Box Dimensions: 3"H x 5"W x 8"L WT: 0.75 lbs UPC: 768170110324

Read more less

All-Stainless Mini Compact Single Horn - 12V Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 db@ 1 Meter Features: All Stainless Steel Inside & Out 304 Stainless Steel inside and out including a sealed sound unit No rust Guaranteed for 5 years. All meet ABYC A-23 for boats up to 12 meters Pre-wired It fits existing hole patterns Specifications: Voltage - Input Range (Volts): 12v Color: Stainless Box Dimensions: 3"H x 5"W x 8"L WT: 0.85 lbs UPC: 768170100363

Read more less

MKP-34 Prop & Nut Kit E Quickly, easily remove or replace your prop with this kit. Each kit includes a prop nut and washer. A crescent wrench is required for installation. Compatible with Minn Kota Props: MKP-33 Weedless Wedge 2 (part number 233160 / 1865018) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Brochure (pdf)

Read more less

Kit OB - Hose Kit for Single Station InstallationConsists of a pair of high pressure hoses supplied with preassembled fittings on both ends.Length: 26 FeetFittings: ORFS Specifications: Cable Length (Feet): 26' Box Dimensions: 5"H x 15"W x 15"L WT: 4.5 lbs UPC: 702755015970

Read more less

M66 Fast Connect Rotary Steering Cable - UniversalSteering Helm: Ultraflex T71FC T72FC - T73NR FC T81FC - T82FC T83NR FC Teleflex Safe TQC/NFB Morse D290Ultraflex Year 2001 & Prior: T71 - T72 - T73NR T74NR - T81 - T82 T83NR - T84NR *Length: 9 Feet Specifications: Cable Length (Feet): 9' Box Dimensions: 3"H x 13"W x 28"L WT: 5.65 lbs UPC: 702755017073

Read more less

90 Degree Mounting Bezel Black90-degree mounting bezel for T73NRFC Non-Reversible Steering System.

Read more less

T71FC Single Cable Rotary Steering HelmFeatures: Fast connect, simple installation All stainless steel cable output ends Corrosion resistant materials Particularly suitable where clearance is limited Standard 3/4" tapered shaft Lock-to-lock steering wheel turns: approx. 3,8 Specifications: Stroke: 9" (228 mm) Maximum allowable steering wheel diameter: 16" (406 mm) Minimal feedback Compact for mounting *The wheel is not included

Read more less

Hustler® - Right Hand - Aluminum Propeller - H2-1208 - 3-Blade - 12.5" x 8 PitchTurning Point has built their reputation on a relentless focus on engineering the best performing aluminum propellers in the World. Utilizing state-of-the-art Squeeze Casting technology, they produce Hustler 3 Blade Propellers that run as fast as their competitors' Stainless Steel Props, and even sometimes faster! Super stiff metallurgy, unique blade geometry, aggressive pitch, rake, and cup all give you the best they can offer: Stainless Performance at Aluminum Prices! Not only does top speed, handling and hole shot improve, but also mid-range performance, which will save you a ton in gas usage. If you want the most your boat and engine combination can offer, then the Hustler 3 Blade delivers.The Three Blade Hustler is great for boaters looking to get the most top end out of their boat, and offer excellent bow lifting capabilities. These props are perfectly matched to mid-range horsepower pontoons, fishing, ribs, and tiller boats. It will fit all 6-75hp outboards with 2.5", 3", and 3.5" gearcases from all engine manufacturers.Squeeze Cast for Added StrengthStainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.Long Lasting Ultracoat™ Powder Coated FinishExclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.Large Free Flowing Exhaust PortsTurning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.Turning Point manufactures Hustler propellers to fit 6-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.  WARNING: This product can expose you to chemicals including CARBON BLACK which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Diameter (Inches): 12-1/2" Material: Aluminum Pitch: 8 Rotation: Right Box Dimensions: 6"H x 13"W x 13"L WT: 4.35 lbs UPC: 652480100789 Quick Guide (pdf)Brochure (pdf)

Read more less

Turning Point Hub Kit: 506Features Lifetime Warranty Never buy another hub kit system again Inner splines adapt to the engine Outer hub compatible with different props Reduce gear shock & engine/drive damage Save up to 30% when purchasing a replacement prop Eliminate propeller vibration & chatter Eliminate hub cracking & failure Corrosion resistant materials - brass splines Reduce gear shock & engine/drive damage Compatible with Michigan Wheel® XHS® and Mercury® Flo Torq® hub kits, but greatly increases ease of installation, durability, and shock absorption value. Also adapts to all Michigan Wheel® and Mercury® interchangeable propellersWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)Brochure (pdf)

Read more less