Shift Knob - 1-7/8" - Smooth Stainless Steel Finish Features: 316 Cast Stainless Steel 1-7/8" Shift Control Knobs Fit Hynautic D-Dec/Sturdy Controls Meets ABYC Specifications

Read more less

Flush Mount Hose AdapterPerfect solution to remove that unsightly hose bib deck fitting and rusty knob. This will enable you to connect your water hose in seconds.Enables you to quick-connect your water hose in seconds. Position this fitting close to your anchor windlass to clean muddy anchors, or locate one on each side of your vessel to make cleanups much easier. Combine the deck washdown fitting with a hose coil washdown hose and keep the deck clutter free.Features: Extra 3/4" GHT male hose adaptor suitable for HoseCoil Water flow available with an easy twist of the fitting Easy to install Position this fitting close to your anchor windlass to clean those muddy anchors. Or locate one on each side of your vessel to make those cleanups much easier Just combine the Quick Release Deck Washdown fitting with a Hose Coil Washdown hose and a high volume Jabsco PAR-Max 4 Washdown pump to keep the deck clutter free Comes with a pre-installed check valve that connects your hose with a simple twist to the deck fitting, even under full pressure Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 8"W x 8"L WT: 0.3 lbs UPC: 671880550253

Read more less

Premium Buffing BrushesTurn Your Buffer Into A Power Brush6-1/2" Medium Brush - Yellow PolystyreneModerately abrasive brush. Specifications: Type: Tools & Accessories Box Dimensions: 3"H x 5"W x 5"L WT: 0.6 lbs UPC: 703485120774

Read more less

V-Throttle - 42018 H - for 0-5V interfaces (voltage)Throttle with analog voltage interfaceRedundant voltage input, IVS, PWM output.They supply the throttle electronic signal. Required for use with direct connection to electronic throttle on the engine.IP protection: IP65Dim.: 205mm x 110mm (8" x 4.3") Quick Guide (pdf)Brochure (pdf)

Read more less

Shift Unit - 42023 AIt controls up to 2 shifts with solenoids. Required for use with direct connection to the electrical shift unit on the transmission.IP protection: IP65Dim.: 210mm x 120mm (8.3" x 4.7") Quick Guide (pdf)Brochure (pdf)

Read more less

Shift Cable - 42060 GSolenoid connection cableOne each solenoid shiftLength: 1M (3.3') Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Single Engine w/out TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with: CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Single Engine w/TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with:= CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Power A Mark II™Electronic Control System - Twin Engines w/TrimThe easy to install Power A Mark II™ control system provides fingertip operation of throttle and shift levers. Using reliable and precise digital data transmission, this single or dual function control system is specifically designed to work on mechanically controlled as well as electronic and electro-hydraulic gas and diesel inboards, sterndrives and outboards. The Power A Mark II™ comes with many features including Dock Assist, which offers the operator the opportunity to reduce the sensitivity of the throttle function for easier dockside handling.Other standard features include RPM Synchronization, which reduces engine vibration and improves fuel economy, a High Idle feature to increase RPM where higher idle is necessary for cold engine operations, a programmable Trolling Valve Control and neutral Warm Up.The stylish and ergonmically designed control makes the Power A Mark II™ suitable for many types of applications ranging from sport boats, yachts and commercial applications.Available with and without trim, the control has audible and visual interfaces which alert the operator to the current status of the control system.With the ability to control up to 2 engines from up to 4 different stations, the Power A Mark II™ is a modular and flexible system with simple to install components.The unique Control Unit Display of the Power A Mark II™ provides simple touch pad programming with descriptive information regarding the set up, tuning and diagnostics of the system.The Power A Mark II™ is a system that can replace mechanical controls either on fully mechanical engines, or on fully electronical engins, or on engines with the combination of both characteristics.Technical Features: Single Lever/Dual Function and Dual Lever/Dual Function for shift, throttle and trolling Up to 4 control stations Power supply: min 9 max 32V Working temperature: -25°C to +75°C Control station functions:- Station Select- Engines Warm up- High idle- Docking- Engine synchronization- Trolling valve Electronic throttle outputs:- Voltage (double output 0 - 5V and 0 - 2,5V)- PWM (0-100%, frequency from 200Hz to 1kHz)- Current (4 - 10mA) Digital Throttle Output:- SAE J 1939- NMEA 2000 Trolling valve output- Voltage (0 - 5V)- PWM (0-100%, frequency from 100Hz to 1 kHz)- Current (4 - 20mA) Electric shift control: - 2 or 3 ON/OFF or proportional solenoids- Shift delays fully settable Safety Devices: Start in-gear PROTECTION(start inhibition with shifted gear) Audible and visual diagnostic failure alarm (READABLE MESSAGES ON THE CONTROL UNIT DISPLAY) Proportional shift delays Programmable working parameters Meets CEI EN 60945 standards EMC Certification and CE MARKConforms with: CEI EN60945 UNI-EN ISO 11547 COMPATIBILITY WITH ALL MECHANICAL THROTTLE ENGINESCOMPATIBILITY WITH ALL ELECTRONIC THROTTLE ENGINESCummins, Detroit Diesel, Scania, Iveco, FPT, Lombardini, VM Motori, FNM, Yanmar, CMD-Volkswagen, Hyundai ecc. The Power A Mark II™ electronic system actuators cannot be installed in those rooms where ignition-proof devices are required. Quick Guide (pdf)Brochure (pdf)

Read more less

Mini Compact Single Hidden Horn - 12V Features: 304 Stainless Steel Trumpets, Diaphragm, and Mounting Brackets Meets ABYCA-23 for boats up to 12 meters Pre-wired Fits existing hole patterns Much louder than competitive models Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 db@ 1 Meter Specifications: Voltage - Input Range (Volts): 12v Box Dimensions: 2"H x 5"W x 8"L WT: 0.7 lbs UPC: 768170110317

Read more less

All-Stainless Mini Compact Single Hidden Horn - 12V Features: All Stainless Steel Inside & Out 304 Stainless Steel inside and out including a sealed sound unit No rust Guaranteed for 5 years. All meet ABYC A-23 for boats up to 12 meters Pre-wired Fits existing hole patterns Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 dB @ 1 Meter Specifications: Voltage - Input Range (Volts): 12v Color: Stainless Box Dimensions: 3"H x 5"W x 8"L WT: 0.75 lbs UPC: 768170110324

Read more less

All-Stainless Mini Compact Single Horn - 12V Specifications: Dimensions: 3"L, 3-1/4"W, 1-3/4"H (7.5 x 8 x 4.5 cm) Max Amp Draw: 3 Amps Rating: 105 db@ 1 Meter Features: All Stainless Steel Inside & Out 304 Stainless Steel inside and out including a sealed sound unit No rust Guaranteed for 5 years. All meet ABYC A-23 for boats up to 12 meters Pre-wired It fits existing hole patterns Specifications: Voltage - Input Range (Volts): 12v Color: Stainless Box Dimensions: 3"H x 5"W x 8"L WT: 0.85 lbs UPC: 768170100363

Read more less

Kit OB - Hose Kit for Single Station InstallationConsists of a pair of high pressure hoses supplied with preassembled fittings on both ends.Length: 26 FeetFittings: ORFS Specifications: Cable Length (Feet): 26' Box Dimensions: 5"H x 15"W x 15"L WT: 4.5 lbs UPC: 702755015970

Read more less

90 Degree Mounting Bezel Black90-degree mounting bezel for T73NRFC Non-Reversible Steering System.

Read more less

T71FC Single Cable Rotary Steering HelmFeatures: Fast connect, simple installation All stainless steel cable output ends Corrosion resistant materials Particularly suitable where clearance is limited Standard 3/4" tapered shaft Lock-to-lock steering wheel turns: approx. 3,8 Specifications: Stroke: 9" (228 mm) Maximum allowable steering wheel diameter: 16" (406 mm) Minimal feedback Compact for mounting *The wheel is not included

Read more less