Swivel Bracket KitGalvanized swivel top brackets provide vertical and tilting adjustments for trailer bunks.Swivel Brackets for mounting Bunk Boards to Bolster Brackets.Features: Bunk flange holes 3/8" dia. Bunk flange 1-3/8" x 3-1/2" Swivel flange hole 1/2" dia. Swivel flange 2" tall x 3-1/2" 2-1/2" bunk flange hole centers & 1 hole centered 10 gauge material *Sold as kit with (2) brackets, (2) 7/16" x 1" head cap screws, and (2) 7/16" nylon lock nuts.

Read more less

60" Post Guide-On With Unlighted Posts These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp.Features: Mounting hardware included Sold in pairs Adjusts out to 19" each side Fits frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 39" high 2-3/8" diameter white PVC posts. Stands 60" above the trailer frame with white post caps. Made in the USA Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Vertical Bunk Bracket Dimpled - 7-1/2"Adjustable bunk bracket. Used when mounting bunks on edge. Ideal for small craft trailers. A single bracket will allow the bunk board to pivot with the hull as the boat is loaded. Double brackets hold the board in place.Features: 7-1/2" Slot 7/16" x 4-3/8" 11 gauge materical, galvanized finish Dimpled style

Read more less

Bolt-On Fender Step Pad - 3" Left Hand/Right HandThis fender step pad is ideal for the do-it-yourselfer. Step pad can be welded or bolted to your trailer fender. Step pad can also be bolted to your trailer frame with u-bolts. U-bolts NOT included.Features: Galvanized Finish 12 Gauge Steel 1-3/16"H x 3"W x 15-1/4"L Left Hand/Right hand

Read more less

Tail Light ProtectorAdded protection for fragile trailer tail lights. Mounts between the existing tail light mounting brackets and the lamp using the two lamp mounting studs. Mounting holes fit standard DOT brake/tail lamps. No hardware required for installation. Aluminum tread 0.080" thick

Read more less

5' Roller BunkRoller bunks make loading and unloading small craft at very short or even dry ramps easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. May be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards.Features: Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel Supports up to 1500lbs of well distributed weight Mounting hardware not included Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Screwless Flush Mount Rod Holder - 30 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter 2-1/8” Outer diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole No logo on the cap for a sleek, low profile The liner runs the full length of the tube Each rod holder includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket

Read more less

Gen3 Carbon Fiber Outriggers - Black - 22' - PairIncludes: Two Carbon Fiber Outrigger Poles with integrated dual stainless eyes Eight locking screws Two aluminum base sleeves Mesh storage bag Features: Integrated dual halyard 316 stainless steel eyes for running multiple halyards Extra-long non-conductive tip to prevent tangles Solid fiberglass base for greater strength and stability Designed to prevent galvanic reactions Taper-Lok joints create single rigid one-piece poles Straighter and stronger than fiberglass and aluminum poles Sections slide inside one another for collapsible storage Our Gen3 Poles are designed to prevent galvanic reactions, a common problem with anything made from carbon fiber, which keeps your poles looking good and performing at their best. The base of the poles is made of solid fiberglass for greater strength and stability.Taper-Lok joints are used to fix the pole in its extended position. The Taper-Lok joints wedge tightly together creating a single rigid one-piece pole that runs much straighter than fiberglass or aluminum poles. When ready for storage, simply unscrew and remove the locking pin from each collar and the fully rigid sections slide inside each other collapsing the pole. Taper-Lok gives you all the benefits of a single rigid pole with the added convenience of easy storage.Our Gen3 Carbon Fiber Poles have an extra-long non-conductive tip designed to prevent line tangles in rough waters. These poles have integrated dual 316 stainless steel halyard eyes that are designed for running multiple halyards on one pole. The smooth design of these eyes also prevents any possibility of snags.The base of this pole fits 1-1/2" pole holders, which is the typical size for stainless steel holders. There are two aluminum fitment sleeves included that fit on the base of the poles allowing them to fit 1-5/8" pole holders, which is the typical size for aluminum rod holders.This set also includes a mesh bag for carrying and storing your poles.

Read more less

Flush Mount 30° Nylon Rod Holder - Black Corrosion-free nylon rod holder. These 30° light-duty fishing rod holders are an economical way to add more rod storage. Molded in one piece from UV-resistant Nylon, these rod holders are tough and corrosion-free. Features: 10" tube Cap is 4" long x 3-1/2" wide Installs into a 2-1/16" hole Mount with 3/16" screws (not included)

Read more less

Flush Mount Rod Holder - 30 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 4"H x 4"W x 14"L WT: 2 lbs UPC: 768296010805

Read more less

Flush Mount Rod Holder - 0 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube

Read more less

Hanger Torsion Mounting Hanger - 14" GalvanizedThe torsion axle mounting hanger attaches to 2" wide beams with u-bolts and holds torsion axles on single and tandem trailers with 14" tires and wheels. U-bolt mounting holes are 33-3/4" on center.

Read more less

Bunk Mounting Bracket - GalvanizedThe heavy-duty galvanized hat-style bunk mount bracket attaches the bunk to upright bunk brackets on 3x3 cross members on trailers not exceeding 4,700 lbs capacity.Used primarily for the front bunk support, and on a few "Limited" models, used for rear support also. Measures 3" between uprights.

Read more less

Step Fender - Galvanized Wide Frame - Large 2"C.E. Smith heavy-duty pre-punched galvanized step bracket mounts to a 2" wide frame, one bracket required per step.

Read more less

Step Fender - Galvanized Wide Frame - Large 3"C.E. Smith heavy-duty pre-punched galvanized step bracket mounts to a 3" wide frame, one bracket required per step.

Read more less

8-12 2" BM15 13/16" Galvanized Spring Hanger C.E. Smith heavy-duty galvanized spring hanger.

Read more less

Shackle Tandem Hanger Galvanized Frame Hanger - 3"C.E. Smith heavy-duty equalizer hanger is galvanized and designed to work on 3" wide frame rails.

Read more less

Shackle Tandem Hanger Galvanized Frame Hanger - 2"C.E. Smith heavy-duty equalizer hanger is galvanized and designed to work on 2" wide frame rails.

Read more less

Bow Stop 8.25" Strap Galvanized Mounting BracketC.E. Smith heavy-duty galvanized strap mounting bracket bolts to the cross member on trailers to support the bow stop.

Read more less

Bunk Galvanized Mounting BracketC.E. Smith 11-gauge zinc-plated steel bunk mounting bracket bolts to bolster support brackets to attach bunks and set the proper angle. Bracket measures 3" wide.

Read more less

Plate Bent Bunk Galvanized Mounting BracketC.E. Smith heavy-duty zinc-plated steel bunk mounting bracket bolts to bolster support brackets to attach bunks and set the proper angle. Bracket is 3/16" thick x 3" wide.

Read more less

Strap Bunk Galvanized Mounting Bracket - 16" x 3" x 9"C.E. Smith's heavy-duty galvanized strap bunk mounting bracket bolts to the cross member on a personal watercraft trailer. Specifications: Measures 3/16" x 3" x 9" Strap tie plate required for installation sold separately

Read more less

Strap Bent Channel Upright Short Galvanized Bracket - 9"Specifications: 9" Upright Short Galvinized Bent Channel

Read more less

70 Series Backing Plate for Flush Mount Rod/Cup HolderFeatures: Cast 316L Stainless Steel Distributes pressure evenly over 30 times more surface area than washers

Read more less

80 Series Wrench for Screwless Rod Holder Installation Crowsfoot WrenchFeatures: For use with 80 Series Screwless Rod Holders Allows for installation in locations with limited space This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

70 Series Wrench for Screwless Rod Holder Installation Crowsfoot WrenchFeatures: For use with 70 Series Screwless Rod Holders Allows for installation in locations with limited space This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

8.5" Kit Rod HolderFeatures: Rod holder is used for 1 kite rod Size: 8.5"

Read more less

Screwless Flush Mount Rod Holder - 15 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter 2-1/8” Outer diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole No logo on the cap for a sleek, low profile The liner runs the full length of the tube Each rod holder includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket

Read more less

Screwless Flush Mount Rod Holder - 0 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter 2-1/8” Outer diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole No logo on the cap for a sleek, low profile The liner runs the full length of the tube Each rod holder includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket

Read more less

Flush Mount Rod Holder - 15 Degree w/Drain - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube

Read more less

Flush Mount Rod Holder - 0 Degree - Black Liner with Drain - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube

Read more less

Gen3 Center Rigger Pole - Black - 2-Section - 12'12' Gen3 Carbon Fiber Center Rigger Pole is designed to prevent galvanic reactions, a common problem with anything made from carbon fiber, which keeps your poles looking good and performing at their best.The base of the poles is made of solid fiberglass for greater strength and stability. Taper-Lok joints are used to fix the pole in its extended position. The Taper-Lok joints wedge tightly together creating a single rigid one-piece pole that runs much straighter than fiberglass or aluminum poles. When ready for storage, simply unscrew and remove the locking pin from each collar and the fully rigid sections slide inside each other collapsing the pole. Taper-Lok gives you all the benefits of a single rigid pole with the added convenience of easy storage.Features: One 12’ Carbon Fiber Center Rigger Pole with integrated dual stainless eyes Mesh storage bag Integrated dual halyard 316 stainless steel eyes for running multiple halyards Extra-long nonconductive tip to prevent tangles Solid fiberglass base for greater strength and stability Designed to prevent galvanic reactions Taper-Lok joints create single rigid one-piece poles Straighter and stronger than fiberglass and aluminum poles Sections slide inside one another for collapsible storage Fits 1-1/2” pole holders without aluminum fitment sleeve Fits 1-5/8” pole holders with aluminum fitment sleeve Extended pole length 12’

Read more less

Gen2 Carbon Fiber Center Rigger Pole - 12' - White - SingleGen2 Poles are designed to prevent galvanic reactions, a common problem with anything made from carbon fiber, which keeps your poles looking good and performing at their best. The base of the poles is made of solid fiberglass for greater strength and stability.Taper-Lok joints are used to fix the pole in its extended position. The Taper-Lok joints wedge tightly together creating a single rigid one-piece pole that runs much straighter than fiberglass or aluminum poles. When ready for storage, simply unscrew and remove the locking pin from each collar and the fully rigid sections slide inside each other collapsing the pole. Taper-Lok gives you all the benefits of a single rigid pole with the added convenience of easy storage.Gen2 Carbon Fiber Poles have an extra-long non-conductive tip designed to prevent line tangles in rough waters. These poles have integrated dual 316 stainless steel halyard eyes that are designed for running multiple halyards on one pole. The smooth design of these eyes also prevents any possibility of snags.Features: Integrated dual halyard 316 stainless steel eyes for running multiple halyards Extra-long nonconductive tip to prevent tangles Solid fiberglass base for greater strength and stability Designed to prevent galvanic reactions Taper-Lok joints create single rigid one-piece poles Straighter and stronger than fiberglass and aluminum poles Sections slide inside one another for collapsible storage Specifications: Length (Feet): 12' Finish: White Diameter (Inches): 1-1/2" Construction: Carbon Fiber Box Dimensions: 5"H x 5"W x 91"L WT: 27 lbs UPC: 768296010379

Read more less

Backing Plate for 70 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series.Features Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

Replacement Liner for 70 Series - WhiteReplacement liner for 70 series in-gunnel and clamp-on rod holders. This UV-resistant vinyl liner protects rods.Features: Recessed liner (doesn't come to the top of the tube) Made of white vinyl material

Read more less

Flush Mount Rod Holder - 15 Degree & 9" Depth - Stainless Steel - Cast Gimbal - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: Safe, rounded bottom 316L Stainless Steel 1/2" pipe-threaded drain hole 9" tube Specifications: Angle: 15-degrees Inner Diameter: 1-5/8"  Outer Diameter: 2"  Cap (L x W): 4-1/2 x 3-5/8 inches Specifications: Mounting Style: Flush Length (Inches): 9" Finish: Polished Diameter (Inches): 1-5/8" Construction: Stainless Steel Angle: 15 Degrees Box Dimensions: 5"H x 5"W x 14"L WT: 2.1 lbs UPC: 768296005535

Read more less

Flush Mount Rod Holder - 30 Degree & 9" Depth - Stainless Steel - Cast Bottom - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: 316L stainless steel 1/2 in. threaded drain Specifications: Angle: 30-degrees Length: 9 in. Inner Diameter: 1-5/8 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Diameter (Inches): 1-5/8" Finish: Polished Length (Inches): 9" Mounting Style: Flush Box Dimensions: 4"H x 5"W x 11"L WT: 2.2 lbs UPC: 768296005542

Read more less

Flush Mount Rod Holder - 0 Degree & 9" Depth - Stainless Steel - Cast Bottom - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: 316L stainless steel 1/2 in. threaded drain Specifications: Angle: 0-degrees Length: 9 in. Inner Diameter: 1-5/8 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Diameter (Inches): 1-5/8" Finish: Polished Length (Inches): 9" Mounting Style: Flush Box Dimensions: 5"H x 5"W x 14"L WT: 2.15 lbs UPC: 768296005528

Read more less

Backing Plate for 80 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series.Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

Backing Plate for 70 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series.Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

70 Series Standard Flush Mount Rod Holder - 0 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength. This model has a durable, rounded cast bottom with a hole to drain water. Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a 1/2 in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Specifications: Degrees: 0 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 14"L WT: 1.95 lbs Quick Guide (pdf)

Read more less

70 Series Standard Flush Mount Rod Holder - 15 Degree - Stainless Steel - Gimbal Bar Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength. A built-in gimbal bar on the open bottom allows water to drain and prevents the rod from spinning.Features: 316L stainless steel Fits 2-3/16 in. hole diameter No logo on the cap for a sleek low profile The liner runs the full length of the tube Specifications: Degrees: 15 degrees Bottom Style: Bar Liner Color: Black Inner Diameter: 1-5/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Gimbal Bar: ¼ in. wide x ½ in. tall Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 14"L WT: 1.9 lbs Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 15 Degree - Stainless Steel - Swivel Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 15 degrees Bottom Style: Swivel Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011048 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 0 Degree - Stainless Steel - Swivel Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 0 degrees Bottom Style: Swivel Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011031 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 30 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 30 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011109 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 15 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 15 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 13"L WT: 4 lbs UPC: 768296010843 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 0 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 0 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296010836 Quick Guide (pdf)

Read more less

70 Series Screwless Flush Mount Rod Holder - 30 Degree - Stainless Steel - Cast Bottom - Black Liner - BoxedThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 30 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Outer Diameter: 2-1/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296010331 Quick Guide (pdf)

Read more less