MasterBus Cable - 1M Suitable for data traffic and powering peripheral equipment, this is the only cable you need for your MasterBus network. MasterBus compatible products come standard with two ports, while other equipment requires an interface.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

RJ12 UTP Cable - 10MA cable to connect the BMV shunt to the BMV head unit. An RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

SmartSolar MPPT 150/60-TRThe Victron SmartSolar MPPT 150/60 Solar Charge Controller is Bluetooth accessible via either built-in Bluetooth or the Victron Energy Bluetooth dongle. The VictronConnect app is available for free on both iOS and Android. This app allows you to view plenty of parameters: battery voltage, solar history, load output, flexible battery charge algorithms, plus day/night timing and light dimming options. These solar charge controllers will gather energy from your solar panels fast and efficiently. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in the case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control is connected to the load output. A special interface cable may be needed, please see the manual Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. MPPT: Ultra Fast Maximum Power Point TrackingBy constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

1038 48V Dual USB Charger Contura Switch MountIntelligent device recognition maximizes charge rate for phones, tablets, or other mobile devices.Features: Ideal for golf carts and other 48V systems Spring-hinged lid keeps debris and moisture out Charges at the speed required by specific devices Internal filtering for reduced electronic interference Over temperature protection Conformal coated circuit board for the harsh marine environment Mounts in an existing contura switch aperture Specifications: Max Output Current: 4A DC (total) Input Voltage: 48V DC Input Voltage Range: 32-64V DC Reverse Polarity: Yes Short Circuit Protection: Yes Thermal Overload Protection: Yes USB: 2.0, Type A

Read more less

Double USB & Power Socket Panel with Breaker Switch This injection molded nylon power socket panel accommodates both USB connectors as well as standard power sockets. The dual USB power socket charges two devices simultaneously. Input 12V–24V. Single output DC 5V/2.4A. Total output is 4.8A with the load being split between the two sides as needed. Enough power to charge iPhones, iPads and most other devices. The power socket is rated at a maximum of 12V/16A. Protective dust caps extend the life of the charger. Includes mounting screws and electrical connectors. Includes 16A breaker switch.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Battery Indicator Eyelet M8 (30A ATO Fuse)The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

GX Touch 50 Adapter for CCGX Cut-OutThis adapter is designed to easily replace the CCGX display with the newer GX Touch. Contents of the packaging are the metal bracket, the plastic bezel, and four mounting screws.There are two methods of mounting: “Install including screen” - most secure mounting of the GX Touch display “Install excluding screen” – GX Touch display is easier to remove, and the adapter can be mounted before completing the wiring Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

ROKK Bezel for Surface Mount Charger Need to elevate the Scanstrut Surface Mount Charger for optimal positioning?  Fear not, with this easy-to-install bezel. It will upgrade the charger just enough.Compatible With:ROKK 10W Waterproof Wireless Charger (SC-CW-02F ) - Surface MountIn the Box: Bezel Mounting hardware Instruction manual  *Sold as an Individual Specifications: Type: Parts Box Dimensions: 1"H x 5"W x 5"L WT: 0.1 lbs UPC: 5060114798144

Read more less

ROKK 10W Sub Wireless Integrated Charging PadEngineered to bond underneath & wirelessly charge through all non-metallic materials; GRP, fabric, leather, wood, carbon fiber, and all leading marine traction products, e.g SeaDek and MarineMat.  The result is wireless phone charging capabilities with your finished aesthetic.The IPX6 waterproof 12/24V Qi certified waterproof wireless charging range enables wireless charging for the outdoor environment without needing phone charging cables.Our new upgraded 10W chargers are up to 60% faster and have been designed for the latest generation of power-hungry devices and apps.Your chosen charging area will be completely flush with its surrounding environment and allows for custom branding.Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use on board, with the unique technology housed in an IPX6, fully encapsulated and sealed unit.Case Compatibility:ROKK wireless is designed to work with most slimline phone cases up to .11" (3mm)Features: Compatible with all Qi Wirelessly charging electronics. Unlimited Charge Possibilities - whether you want to integrate wireless charging at the helm, cockpit table, seating areas, bedrooms, or even areas that may be stood on, it’s all possible.  Let your creativity run free and integrate wireless charging into new materials, fabrics, and in high traffic areas of the boat that until now have been off-limits. Technical Specifications: Input Voltage Range - 10-30V DC (12/24V system)  Input current max: - 2A   Output Power: 10W (9V,1.1A) IPX6 Waterproof Qi-certified wireless charging In the Box: Charging pad Instruction manual  *Sold as an Individual Specifications: Type: Chargers Box Dimensions: 1"H x 4"W x 4"L WT: 0.25 lbs UPC: 5060114798076 Quick Guide (pdf)

Read more less

Skylla-i Control GX Remote Panel for Skylla ChargerA modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Features: The right amount of charge for a lead-acid battery: variable absorption time BatterySafe mode: preventing damage due to excessive gassing Storage mode: less maintenance and aging when the battery is not in use Smaller and lighter compared to similar models NMEA2000 Canbus connection PowerControl: set a maximum shore power Remote Control Li-ion (LiFePo4) ready Models:24 VoltPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Wall Surface Mount for BMV or MPPT ControlsWall mount enclosure for BMV or MPPT Control.Warranty InfoPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

Wall Mount Enclosure for Color Control GX & BMV or MPPT ControlWall Mount for CCGX and BMV or MPPT Control easily mounts a CCGX and a BMV-700 series or MPPT Control on a wall. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

RJ45 UTP - 20M CableA cable to connect Phoenix Inverter Control, VE Interface MK3-USB, and VE.Bus connections between multiple VE.Bus devices and GX devices.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Venus GX Control - No DisplayFeatures: Venus GX The Venus GX provides intuitive control and monitoring for all Victron power systems. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT solar chargers, BMV battery monitors, Lynx Ion + Shunt and more.  VRM Online Portal All readings are forwarded to our free remote monitoring website: the VRM Online Portal. To get an impression, try the demo on https://vrm.victronenergy.com. See also the screenshots below.  Remote Console on VRM The way to access the device for setting up, as well as monitoring, is via Remote Console. Either via VRM, via the built-in WiFi Access Point, or on the local LAN/WiFi network.  Automatic genset start/stop A highly customizable start/stop system. Use state of charge, voltage, load and other parameters. Define a special set of rules for quiet times, and optionally a monthly test run.  Data logging When connected to the internet, all data is sent to the VRM Portal. When there is no internet connection available, the Venus GX will store the data internally, up to 48 hours. By inserting a micro SD-card or USB stick, more data can be stored. These files can then be uploaded to the VRM Portal, or offline converted with the VictronConnect app, for analysis. Supported products - Multis and Quattros, including split-phase and three-phase systems. Monitoring and control (on/off and current limiter). Changing configuration is possible (only remotely via the internet, not without an internet connection). - EasySolar 1600VA - BlueSolar MPPT Solar Chargers with a VE.Direct port. - BlueSolar MPPT 150/70 and the MPPT 150/85 with VE.Can port. - SmartSolar MPPT 150/70 and the MPPT 150/100 with VE.Can port. When multiple BlueSolar MPPTs or SmartSolar MPPTs with VE.Can are used in parallel, all the information is combined as one. See also our blog-post about synchronizing multiple MPPT 150/70 solar chargers. - BMV-700 family can be connected directly to the VE.Direct ports on the Venus GX. Use the VE.Direct Cable for this. - BMV-600 family can be connected to the VE.Direct ports on the Venus GX. Requires an accessory cable. - Lynx Ion + Shunt - Lynx Ion BMS - Lynx Shunt VE.Can - Skylla-i battery chargers - NMEA2000 tank sensors - A USB GPS can be connected to the USB port. The data is sent to the VRM Portal for tracking purposes. The map on VRM will show the latest position. - Fronius PV Inverters When more than two VE.Direct products must be connected, USB can be used. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

RJ45 UTP - 30M CableA cable to connect Phoenix Inverter Control, VE Interface MK3-USB, and VE.Bus connections between multiple VE.Bus devices and GX devices.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

VE. Direct - 0.9M Cable (1 Side Right Angle Connector)Features: Cable Length: 0.9M 1 Side Right Angle Connector Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

ROKK Wireless Phone Receiver Patch - Micro USBDesigned and engineered by the outdoor technologies experts Scanstrut, the new ROKK wireless charging receiver patches are wireless charge ready!  Simply plug the Mirco USB charge patch into your phones charging port, place on the back of the phone and then clip on your phone case over the top.  Your phone is now ready to be charged by any of the 12/24V ROKK wireless charger range or any other Qi-certified charging product. Convert non-wireless charging enabled micro USB chargeable phones to wireless charger compatible.Compatibility: Phones with Micro USB*Sold as an Individual Specifications: Type: Chargers Box Dimensions: 1"H x 3"W x 8"L WT: 0.05 lbs UPC: 819505020440 Brochure (pdf)

Read more less

ROKK Wireless Phone Receiver Patch - LightingDesigned and engineered by the outdoor technologies experts Scanstrut, the new ROKK wireless charging receiver patches are wireless charge ready!  Simply plug the Mirco USB charge patch into your phones charging port, place on the back of the phone and then clip on your phone case over the top.  Your phone is now ready to be charged by any of the 12/24V ROKK wireless charger range or any other Qi-certified charging product. Convert non-wireless charging enabled Lighting chargeable phones to wireless charger compatible.Compatibility: iPhone's with Lighting charging port  *Sold as an Individual Specifications: Type: Chargers Box Dimensions: 1"H x 3"W x 7"L WT: 0.25 lbs UPC: 819505020433 Brochure (pdf)

Read more less

28" Adjustable Solar Panel Tilt MountSamlex Solar RV panel ADJ-28, tilt mounts are adjustable to fit any of the Samlex solar panels from the off-grid Solar Charging Kits. Features: Convenient - Adjustable Solar Mounts Light - Aluminum Specifications: Weight - 4.8 (lbs) Weight - 2.17 (kg) Dimensions - 28 x 1 x 1 (in) Dimensions - 71.1 x 2.5 x 2.5 (cm) Warranty - 2 Year Limited WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Owner's Manual (pdf)Brochure (pdf)

Read more less

Dual USB Rocker Switch Style Voltmeter with Hidden Display This Dual USB Rocker Switch Style Voltmeter fits into any standard 13/16” X 1-7/16” hole. Allows two devices to be charged simultaneously while also displaying the batteries output. The total output 4.8A load is split 2.4A per side. Enough power to charge phones, pads, and tablets quickly and efficiently. Input 12-24VDC. Output DC 5V/4.8A. Red LED display. IP65 rating.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Dual USB Socket/Voltmeter with Hidden Display This Dual USB Socket allows for two devices to be charged simultaneously while also displaying the batteries output. The total output 4.8A load is split 2.4A per side as needed. Enough power to charge phones, pads, and tablets quickly and efficiently. Also fits Sea-Dog® Power Socket Shell 426100. Output DC 5V/4.8A. Input 12-24VDC. Red LED display. IP65 rating.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Dual USB Power Plug with Voltage/Amp Meter LCD screen displays charging status in amps, battery voltage, and low voltage audio alarm. Stamped stainless steel and injection molded nylon construction this USB power plug adapter charges two devices simultaneously. Input 12-24V, Single output DC 5V/2.4A. Total output is a 4.8A with the load being split between the two sides as needed. Enough power to charge iPhones, iPads and most other devices. Can be used on a boat, car, or RV. This portable version fits all Sea-Dog® Power Sockets and any standard 12V receptacle.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

AC Power Supply 20/25A, 12V Out, 85-265V InThe PWI320 Intelligent Power Supply delivers a full 300 watts of output power for communications, control or a wide variety of other devices. It is fully Digital Signal Processor controlled and feature Universal Input Voltage from 85 to 265 VAC at 50 or 60 Hz with Active Power Factor Correction for the most efficient use of AC power.The Power Supply is preset to the same voltage as a fully charged battery of the nominal output voltage (ie. 13.6V for a 12V model, etc.). The voltage can be adjusted over a reasonable range using the front panel controls, or the PowerWizard software that is free to download from www.analyticsystems.com.Seven dual color LEDs clearly indicate output current levels as well as indicating faults with the Power Supply. Safety features include Power Supply over temperature shutdown, current limiting, short circuit protection, input under voltage shutdown and output overvoltage protection all with automatic recovery.  PWI320MW model available with MIL connectors, extra input and output filtering and sealed to IP66Features: Digital Signal Processor controlled Universal worldwide AC input Computer programmable Simple front panel controls Easy connection to loads High Vibration Rugged Duty Dry Contact Output Fail Relay Carrying Handle Canbus / RS232 / Remote Control port Five year parts and labour warranty

Read more less

Water Resistant USB Accessory Panel - 15A Circuit Breaker, 4x Blank Apertures Easy to install accessory panels include a 15A circuit breaker switch and pre-wired harness. Panels offer customizable 12V charging and monitoring options.Features: Pre-wired harness included in all panels for easy installation Silicon breaker boots and gasket protects against water ingress Illuminated Carling Technologies 15A circuit breaker switch allows the ability to shut off panel preventing parasitic draw Polycarbonate/ABS panel face is UV-stabilized, flame retardant, and will not corrode 12V DC only Specifications: Positions: 1 Nominal Voltage: 12V DC

Read more less

4368 Water Resistant USB Accessory Panel - 12V Socket, 2x 2.1A Dual USB Chargers, Mini VoltmeterEasy to install accessory panels include a 15A circuit breaker switch and pre-wired harness.  Panels offer customizable 12V charging and monitoring options.Features: Pre-wired harness included in all panels for easy installation Silicon breaker boots and gasket protects against water ingress Illuminated Carling Technologies 15A circuit breaker switch allows the ability to shut off panel preventing parasitic draw Polycarbonate/ABS panel face is UV-stabilized, flame retardant, and will not corrode 12V DC only Specifications: Positions: 1 Nominal Voltage: 12V DC

Read more less

Stainless Steel 12V Receptacle with Cap12-Volt Receptacle - High quality, 12V female socket with watertight cap. Stainless steel construction.Features: AFI 12V stainless steel receptacle with cap High quality, 12V female socket, with water tight cap Highly recommended and durable Stainless Steel construction 12V female socket Includes watertight cap WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Universal Temperature SensorUse with the P12 Charger, M2 OLED, and Mini OLED Meters Includes double-sided tape Waterproof design Temperature Range: -40°F to 300°F (-40°C to 150°C) Wire Length: 18" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ProTournament RemoteTri-color charge mode status.Cable length: 12'WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less