Universal Kill Switch with Floating Lanyard This marine emergency cut-off Unversal Kill Switch with Floating Lanyard attaches to your life vest while operating a boat or personal watercraft. Designed to instantly cut battery power when detached. Dual circuitry allows kill switch to be wired for either ignition kill or magneto kill depending on the application. The housing is constructed of weatherproof injection molded nylon and Delrin with 0.250" brass terminals. The switch includes a floating lanyard approximately 15" when coiled and 48" when stretched, which should be replaced if worn, cut, or frayed. Mounting hole is 5/8" in diameter. Maximum panel thickness: 3/8". Maximum 5A draw. WARNING: Switch should be tested for proper function before each use.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

GX Touch 50 Wall MountThe GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

4366 Water Resistant USB Accessory Panel - Circuit Breaker, 12V Socket, Dual USB Charger, Mini VoltmeterEasy to install accessory panels include a 15A circuit breaker switch and pre-wired harness. Panels offer customizable 12V charging and monitoring options.Features: Pre-wired harness included in all panels for easy installation Silicon breaker boots and gasket protects against water ingress Illuminated Carling Technologies 15A circuit breaker switch allows the ability to shut off panel preventing parasitic draw Polycarbonate/ABS panel face is UV-stabilized, flame retardant, and will not corrode 12V DC only Specifications: Positions: 1 Nominal Voltage: 12V DC

Read more less

8263 Contura Single Bilge Pump Control PanelBlue Sea Systems water resistant 12/24 Volt DC Bilge Pump control panel with Contura rocker switch and fuse holder for fuses up to 20ampFeatures: Designed for 12 or 24V DC systems  ON - OFF - AUTO Contura Switch Watertight mounting gasket Fuse holders accept commonly available AGC and MDL glass fuses "ON” LED embedded in switch indicates pump is running Completely wired and ready to install Specifications: Weatherproof - Water Resistant No. of Bilge Pumps - one (1) Nominal Voltage - 12/24V Panel Cumulative Rating - 45A Switch Rating: 20A @ 12V DC / 15A @ 24V DC Dimensions (H x W x D) - 3.75" x 2.25" x 3" Weight - .25lb In the Box: Panel Mount AGC/MDL Fuse Holder (P/N 5021) Contura III Switch SPDT - On - OFF - (ON) (P/N 7944) Black 60 Label Set (P/N 8214) *Sold as an Individual WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: ON-OFF-AUTO Color: Black/Grey Throw/Pole: SPDT Box Dimensions: 3"H x 4"W x 7"L WT: 0.25 lbs UPC: 632085082635 Owner's Manual (pdf)

Read more less

All Digital Electronic ChargingIndustry recognized with the 2010 IBEX Innovation Award, ProNauticP employs our ProMar Digital Performance Charging Platform which combines all digital control and software-based power conversion technology with global energy management features. ProNauticP addresses the trend of incorporating and using more 12-volt electronics on-board today's power, sail, cruising and sport fishing boats. Boasting twelve digitally-controlled performance charging profiles with finger tip selection, ProNauticP fully charges, conditions, maintains and re-conditions batteries while extending battery life and maximizing battery reserve power performance. ProNauticP is Power Factor Corrected with auto-ranging global AC input allowing all models to operate off a standard household power connection. Featuring dual digital displays for real-time display of actual charging voltage and amperage and AC power-on diagnostics with pass or fail status in addition to discreet fault indication for mis-wiring or adverse battery bank conditions. Designed to provide more time on the water enjoying what you like most... boating.ProMar Digital Performance ChargingProMar Digital Charging Performance - 12 Selectable ProfilesUp to 12 performance & precision 4-stage charging profiles: Charge, Condition, Maintain and Re-condition. Automatic dockside power mode for 12 Volt DC lighting and appliances. Factory set for Flooded (Lead Acid) batteries. AGM, GEL selectable.Power Factor Correction - Global AC InputAuto-ranging (100-250VAC/50-60Hz) global AC input with reduced harmonic distortion allowing all models to operate off a household power outlet connection. ProNauticP consumes less power so more AC power is available on board.Distributed On Demand TechnologyAutomatically senses and distributes 100% of available charging amps to any one bank or combination of all banks.Digital Self-Calculating Absorption and Battery Health Re-Conditioning ModeAutomatically programs conditioning time based on discharge state of batteries. Automatically de-sulfates batteries after 21 days in the maintain mode, improving reserve power performance & extending battery life.Conservation Energy Saver ModeAfter 72 hours of not seeing a load greater than 5 amps, float voltage will be lowered consuming less energy during storage periods. (for flooded & sealed charge profiles) Service and Fault Mode LED IndicatorsReal time indication of wiring faults or adverse conditions that may impact the operation of a boat's charging system.Automatic Fan Speed ControlQuiet operation. Innovative front exhaust prevents restriction of air flow and cooling.Automatic Temperature Compensation and Built-in SafetyRemote temperature probe included - Ignition protected and current limiting. Designed and constructed to: Marine ULc 1236, CE, CTick and FCC Class B.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 20a Charging Banks: 3 Portable: No Charger Input - Voltage: 120/240v Charger Output Voltage: 24v Box Dimensions: 6"H x 11"W x 13"L WT: 6.65 lbs UPC: 031669631700 Owner's Manual (pdf)Brochure (pdf)

Read more less

16-14 AWG - #10 Nylon Ring Terminal - 100-PackAncor's Marine Grade terminals differ from automotive terminals by being designed for the harsh marine environment. Nylon insulators are easy to crimp and will not split. Barrels are designed to tightly grip the wire with the least effort. Tinned copper gives the least electrical resistance but the most corrosion protection.Features: Nylon insulated with insulation grip Double crimp, funnel entry UL 486C WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Gauge: 16-14 AWG Type: Ring Terminals Post Size: #10 Package Qty: 100 Heat Shrink: No Box Dimensions: 1"H x 3"W x 5"L WT: 0.2 lbs UPC: 091887221848 Brochure (pdf)

Read more less

Nylon Fully Insulated Disconnect - Female - 22-18 - 100-PieceAncor's Marine Grade terminals differ from automotive terminals by being designed for the harsh marine environment. Nylon insulators are easy to crimp and will not split. Barrels are designed to tightly grip the wire with the least effort. Tinned copper gives the least electrical resistance but the most corrosion protection.Features: 0.250 (6.4 mm) tab size Nylon insulated with insulation grip Double crimp, funnel entry UL 310 Specifications: Gauge: 22-18 AWG Type: Disconnects Package Qty: 100 Heat Shrink: No Box Dimensions: 1"H x 3"W x 5"L WT: 0.25 lbs UPC: 091887228359

Read more less

ATO/ATC Fuse Pack - 1 Amp - 25-PackFeatures: Fast-acting type fuses ideal for electronic devices Standard circuit protection device for automobiles and trucks Tin-plated connector blades for corrosion resistance Specifications: Amperage: 1 Amp Maximum Voltage: 32V DC Interrupt Capacity: 1000A WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 1a Fuse Type: ATO/ATC Type: Fuses Box Dimensions: 1"H x 2"W x 4"L WT: 0.1 lbs UPC: 632085523510

Read more less

14" UV Black Standard Cable Zip Ties - 25 PackAncor offers a wide variety of materials, styles, and sizing options. A DoubleLock design offers increased tensile strength that is 33% stronger than the industry standard cable tie. With a unique design and high-quality construction, Marinco cable ties provide a great solution for bundling wire, cable, hoses, cords and countless other applications.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Cable Ties Box Dimensions: 2"H x 2"W x 15"L WT: 0.2 lbs UPC: 093344501517

Read more less

PROwatt SWInline Transfer RelayAn easy to mount 15A Inline Transfer Relay provides switching between shorepower and inverter AC source. It comes with a power plug for convenient connection to the inverter GFCI and a hardwire cord for the AC input and output interface. It is available as an accessory to the Prowatt SW product line.WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

Read more less

Black 18 AWG Primary Wire - 1,000' Pacer's marine wire is designed to handle the harshest marine environments.  It is manufactured to meet and exceed the most stringent specifications.  This 18 AWG marine wire is constructed in the USA to achieve the highest level of quality. Built from Type III class K tinned copper, this wire offers excellent flexibility.  The tinned copper also resists corrosion adding to the life of the wire.  What about the insulation?  After the copper is tinned it is then insulated with a durable and flexible PVC jacket.  The jacket makes this 18 AWG marine wire resistant to alkali, abrasion, acid, gas, oil, flame, and moisture.  What standards and compliances does this wire meet?  Pacer's marine wire exceeds the requirements and standards of UL, ABYC, and NMMA. Features: Built for durability, flexibility, and longevity in the harshest marine environments  So flexible that you can tie it into a knot without compromising any of its qualities  Proprietary insulation ensures the highest level of protection available  Ease of installation and the longevity of its design have helped solidify this marine wire as the choice of boating professionals Compliances: UL Standard - 1426 BC-5W2 U.S.C.G - 33 CFR part 183  ABYC - E-11.14  Technical Specifications: Conductor - Type III annealed finely stranded tinned copper ASTM B172 Class K Insulation -20 °C to 105 °C flexible, color-coded PVC Voltage Rating - 600-V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil and Moisture *Sold as an Individual Specifications: Color: Black Gauge: 18 AWG Length (Feet): 1,000' Box Dimensions: 7"H x 7"W x 7"L WT: 11.1 lbs UPC: 840248200851 Brochure (pdf)

Read more less

Yellow 18 AWG Wire Ferrule - 6mm Length - 25 PackWire fraying can quickly become a problem when dealing with IEC (European)-style terminal blocks. As the wire frays, the connection becomes weaker, and the problem will need to be addressed. But all that can be prevented. How? By utilizing wire ferrules. Wire ferrules are a type of terminal that prevents wire fraying. It covers the stranded wire and creates a solid, connected piece. In a sense, wire ferrules make stranded wire behave like solid wire. This is important, especially when working with IEC terminal blocks.How are wire ferrules properly used? The first step is to strip the wire to the correct length. Now slide the ferrule over the exposed wire. Make sure that the nylon casing butts up to the wire insulation. Once set, crimp using the proper tool. Using the proper tool is important, as, without the proper pressure, the wire may not create a solid connection. Proper crimping pressure and technique are key to ensuring continued performance. Once properly crimped, users can add heat shrink for added protection if they choose. Features: Prevent strand separation while minimizing strand breakage Insulated ferrules provide additional electrical insulation Increase connection reliability when terminating stranded wire in terminal blocks Specifications: Package Size: 25 Wire Size (AWG): 18 Insulation Color: Yellow Ferrule Length: 6mm (0.24 in.) Stripping Length: 8mm (0.31 in.) Quick Guide (pdf)

Read more less

Grey 10 AWG Primary Wire - 20'Pacer's marine wire is designed to handle the harshest marine environments.  It is manufactured to meet and exceed the most stringent specifications.  This 10 AWG marine wire is constructed in the USA to achieve the highest level of quality. Built from Type III class K tinned copper, this wire offers excellent flexibility.  The tinned copper also resists corrosion adding to the life of the wire.  What about the insulation?  After the copper is tinned it is then insulated with a durable and flexible PVC jacket.  The jacket makes this 10 AWG marine wire resistant to alkali, abrasion, acid, gas, oil, flame, and moisture.  What standards and compliances does this wire meet?  Pacer's marine wire exceeds the requirements and standards of UL, ABYC, and NMMA. Features: Built for durability, flexibility, and longevity in the harshest marine environments  So flexible that you can tie it into a knot without compromising any of its qualities  Proprietary insulation ensures the highest level of protection available  Ease of installation and the longevity of its design have helped solidify this marine wire as the choice of boating professionals Compliances: UL Standard - 1426 BC-5W2 U.S.C.G - 33 CFR part 183  ABYC - E-11.14  Technical Specifications: Conductor - Type III annealed finely stranded tinned copper ASTM B172 Class K Insulation -20 °C to 105 °C flexible, color-coded PVC Voltage Rating - 600-V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil and Moisture Length - 20 ft. Guage (AWG) - 10 Color – Grey *Sold as an Individual Specifications: Color: Grey Gauge: 10 AWG Length (Feet): 20' Box Dimensions: 3"H x 5"W x 5"L WT: 1.05 lbs Brochure (pdf)

Read more less

DC Digital Multimeter w/ Alarm Displays amperage from -500 to +500 Amps Displays voltage from 0 to 60 Volts in 0.01 Volt increments High and low voltage, audio and visual alarms Standard meter operates in negative side of circuit only. Shunt Shifter required for positive side installation such as alternators 3 levels of display brightness Programmable sleep mode blanks display for power conservation Splashproof front Includes 500 Amp shunt Applicable for 12, 24, 32, 36, and 42 Volt DC systems WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

SmartShunt 1000AMP/50MV Bluetooth Smart Battery ShuntThe SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

Stainless Steel Low-Profile Cable Seal for Cables 4-9mmThe DS-LP-21A-S Low-Profile Cable Seal is engineered to effortlessly accommodate cables ranging from 4–9 mm (0.15"–0.35") and connectors up to Ø21mm (0.82"), ensuring a seamless and impact-resistant solution.Premium ConstructionCrafted with attention to detail, its marine-grade 316 stainless steel construction is not only aesthetically pleasing but also built to thrive in the outdoor environment. 316 stainless steel has exceptional corrosion resistance and durability, making it the perfect choice for withstanding the elements and ensuring the installation remains intact even in the harshest conditions. The fine finish of Scanstrut's 316 stainless steel design adds a touch of sophistication to the installation, elevating both the form and function of the cable installation.Low-Profile DesignThe Scanstrut slimline design was purpose-built to reduce the overall mounting height of the cable seal by 68% in comparison to Scanstrut's DS21A-P seal. This translates to a clean, flush, more refined look.Watertight InstallationAchieve peace of mind with Scanstrut watertight installation. The tapered bung forms a secure seal, while every unit has a closed-cell base seal for 100% waterproof assurance. All models have undergone rigorous IP68 testing and approval to ensure they are outdoor-ready.Effortless and Repeat InstallationsFeaturing captive nuts to simplify assembly and allow for reliable repeat installations. Each unit is supplied with pre-drilled and blank bungs, streamlining the setup process. Also, there's no need to remove the cable connector during installation, thanks to the convenient split-seal option.Features: IP68 Waterproof Designed for 4–9mm cables (0.15"–0.35") UV Resistant Constructed from marine-grade 316 stainless steel No messy sealant, ensuring a tidy finish Simplified installation that saves you time and effort Guaranteed 100% watertight seal Perfect for solar panels, light bars, rooftop electronics, and more Each cable seal is installed by using a hole saw, keeping seal technology below the mounting surface Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 9"L WT: 0.45 lbs UPC: 5060114798618 Quick Guide (pdf)

Read more less

Remote Control Panel w/(3) 2145 Remote Control Contura SwitchFeatures: Lockout slides reduce the risk of accidental switching For use with ML-Series Switches Includes labels illustrated only Over 500 individual labels available Specifications: Positions:3 Nominal Voltage:12V DC / 24V DC Height:4.75" (120.65mm) Width:4.88" (123.95mm) Depth:2.00" (50.8mm) Weight:0.83lb (0.38kg)Includes:(3) - 2145 - SPDT Remote Control Contura Switch - (ON)-OFF-(ON) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: AC/DC: DC Box Dimensions: 6"H x 7"W x 9"L WT: 0.8 lbs UPC: 632085011482 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Cut/Strip/Crimp Multi Tool - 22-10 AWGFeatures: Precision ground cutters and stripping station Capacity: Crimps 22 AWG to 10 AWG/0.3 to 5mm2 solid and stranded wires Cuts (4) 40/2mm, (6) 32/4mm, (8) 32/4.8mm, (10) 32/6.4mm and 10-24/6.4mm bolts Length: 8.6" (20.3cm) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ANL-Fuse 400A/80V for 48V Products (Package of 5)Victron Energy's ANL fuses are bolt-down fast-acting and have a higher short-circuit breaking capability than MEGA fuses. This particular pack of Victron ANL fuses contains FIVE 400-amp fuses.Features:For 48V productsSpecifications: Max Current Rating: 400 amps Max Voltage Rating: 80 volts Approximate Voltage Drop: 125 mV Cold Resistance: 0.3 mΩ Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 400a Fuse Type: ANL Type: Fuses Box Dimensions: 1"H x 5"W x 6"L WT: 0.3 lbs UPC: 8719076061786 Quick Guide (pdf)Brochure (pdf)

Read more less

MultiPlus 12/3000 - 120-50 - 230V - VE.BusThe MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, and multiple system integration features.Two AC OutputsThe main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output (a second output is available on models rated at 3 kVA and more).Virtually Unlimited Power Thanks to Parallel OperationUp to 6 Multis can operate in parallel to achieve a higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 AMP charging capacity.Three Phase CapabilityIn addition to parallel connections, three units of the same model can be configured for three-phase output. But that’s not all up to 6 sets of three units can be connected in parallel for a 75 kW / 90 kVA inverter and more than 2000 Amp charging capacity.PowerControl - Dealing with Limited Generator, Shore Side or Grid PowerThe MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shoreside supply (nearly 10 A per 5 kVA Multi at 230 VAC). With the Multi Control Panel, a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.PowerAssist - Boosting the capacity of shore or generator powerThis feature takes the principle of PowerControl to a further dimension. It allows MultiPlus to supplement the capacity of the alternative source. Where peak power is often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces the spare power is used to recharge the battery.Solar energy: AC Power is Available Even During a Grid FailureThe MultiPlus can be used in off-grid as well as grid-connected PV and other alternative energy systems. Loss of mains detection software is available.System Configuring: In the case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software Off-grid, grid-interactive, and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications) On-site Monitoring and ControlSeveral options are available: Battery Monitor, Multi Control Panel, Color control for GX or other GX devices, smartphone, tablet (Bluetooth Smart), laptop, or computer (USB or RS232).Remote Monitoring and ControlColor Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.Remote ConfiguringWhen connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed, and settings can be changed remotelySpecifications: PowerControl: Yes PowerAssist: Yes Transfer Switch (A): 16 or 50 Inverter Specifications: Input Voltage Range (V DC): 9,5 – 17 V 19 – 33 V 38 – 66 V Output: Output voltage: 230 VAC, ± 2% / Frequency 50 Hz ± 0,1% Continuous Output Power at 25°C (VA): 3000 Continuous Output Power at 25°C (W): 2400 Continuous Output Power at 40°C (W): 2200 Continuous Output Power at 65°C (W): 1700 Peak Power (W): 6000 Maximum Efficiency (%): 93 / 94 / 95 Zero Load Power (W): 20 / 20 / 25 Zero Load Power in AES Mode (W): 15 / 15 / 20 Zero Load Power in Search Mode (W): 8 / 10 / 12  Charger Specifications: AC Input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz / Power factor: 1 Charge Voltage Absorption (V DC): 14,4 / 28,8 / 57,6 Charge Voltage Float (V DC): 13,8 / 27,6 / 55,2 Storage Mode (V DC): 13,2 / 26,4 / 52,8 Charge Current House Battery (A): 120 / 70 / 35 Charge Current Starter Battery (A): 4 (12 V and 24 V models only) Battery Temperature Sensor: Yes General Specifications: Auxiliary Output: Yes (16A) Programmable Relay: Yes Protection: a - g VE.Bus Communication Port: For parallel and three-phase operation, remote monitoring, and system integration General purpose com. Port: Yes Remote On-Off: Yes Common Characteristics: Operating temp. range: -40 to +65°C (fan-assisted cooling) / Humidity (non-condensing): max 95% Enclosure Specifications: Common Characteristics: Material & Color: aluminum (blue RAL 5012) / Protection category: IP 21 Battery-Connection: Four M8 bolts (2 plus and 2 minus connections) 230 V AC-Connection: Screw terminals 13mm^2 (6 AWG) M6 bolts Weight (kg): 18 Dimensions (hxwxd in mm): 362 x 258 x 218 Standards Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1 Emission, Immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 Road Vehicles: 12V and 24V models: ECE R10-4 Anti-Islanding: See Victron's website Can be adjusted to 60 HZ. 120 V models available on request Protection Key: Output short circuit, overload, battery voltage too high, battery voltage too low, temperature too high, 230 VAC on the inverter output, input voltage ripple is too high Non-linear load, crest factor 3:1 Up to 25°C ambient Switches off when no external AC source is available Programmable Relay That Can, Among Other Things, Be Set for General Alarm Including DC Undervoltage or genset start/stop function / AC rating: 230 V/4A / DC rating: 4 A up to 35 VDC, 1 A up to 60 VDC / A.o. to communicate with a lithium-ion battery BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

VE.Bus BMS V2 for Victron LiFePO4 Batteries 12-48VDC - Work with All VE.Bus & GX DevicesThe VE.Bus BMS and VE.Bus BMS V2 is Battery Management System (BMS) designed to interface with and protect a single or multiple Victron Lithium Battery 12,8V & 25,6V Smart (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against the over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions.Based on the status of the battery or batteries, the BMS will: Generate a pre-alarm signal to alert of an imminent cell under voltage conditions. Disable inverting in VE.Bus inverters or inverters/chargers via VE.Bus, and disable other loads via the 'Load Disconnect' terminal in the event of a cell under voltage conditions. Disable charging in VE.Bus inverters or inverters/chargers via VE.Bus and disable other chargers via the 'Charge Disconnect' terminal in the event of a cell overvoltage, under-temperature, or over-temperature conditions. The "original" VE.Bus BMS is best used in systems without a GX device The "next generation" VE.Bus BMS V2 has additional features such as: Remote on/off terminals. Ability to disable VE.Direct and VE.Can solar chargers via a GX device. Allowing control of the VE.Bus inverter/charger from multiple devices, like the Digital Multi Control, the VE.Bus Smart dongle and/or a GX device. Auxiliary power input and output terminals that allow a GX device to remain powered in the event of a system shutdown. Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 5MFeatures: 5-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Holder MEGA FuseVictron MEGA Fuse Holder is made of high quality material and very durable, not cheap flimsy plastic. Fits all of Victron’s MEGA fuses.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Fuse Type: MEGA/AMG Type: Fuse Holders Box Dimensions: 2"H x 4"W x 5"L WT: 0.25 lbs UPC: 8719076021704 Quick Guide (pdf)Brochure (pdf)

Read more less

SPST Chrome Plated Long Handle Toggle Switch - ON/OFFSingle pole, single throw toggle switch turns one circuit on and off. Common applications include any single circuit requiring an on-off style switch.Features: Nominal voltage is 12V/24V DC Rated for 25A at 12V DC, 15A at 24V DC Long handle and two 1/4" balde terminals Mounting stem 15/32" fits panels up to 1/4" thick Same as Cole Hersee part number 55055 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: On/Off Color: Chrome Plated Throw/Pole: SPST Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 870216046723

Read more less

TruePower Plus Modified Sine Wave Inverter - 1200WDesigned to convert 12 VDC battery power to 115 VAC and will automatically pass through AC Inlet power when present. TruePower Plus is rich with features including; Innovative dual color digital LCD message center, dual color gauges for AC power output and battery DC input, USB power port, GFCI convenience outlets, DC cable covers, and separate on/off remote. Our integrated AC cable strain reliefs and front screw connection terminal blocks allow for quick and easy installation without the added need for ring terminals for AC power connections. Designed with soft start noise filtered technology and x2 surge capability for powering demanding loads. Shock resistant construction with internal conformal coated electronics for protection in harsh environments. Features: Intuitive dual color digital LCD message center Dual color gauges for AC power output and battery DC input Internal 30 amp AC transfer switch will automatically pass through AC inlet power when present USB power port and GFCI convenience outlets Compact and lightweight design Soft start noise filtered technology with x2 surge capability On/Off remote with 9 foot cable and DC cable covers Included Integrated AC power cable strain reliefs for ease of installation Built-in safety with overload, over temperature, short circuit and reverse polarity protection Audible alarm and shut down for low and high DC voltage, overload and over temperature conditions Shock resistant construction with internal conformal coated electronics 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Inverter Cont. Output Wattage: 1200w AC Connection Type: GFCI Outlet DC Connection Type: Hardwire GFCI: Yes Outlet Qty: 2 Duplex GFCI Inverter Surge Rating: 2400w Inverter Input Voltage: 12v Inverter Output Voltage: 120v Waveform: Modified Sine Wave Box Dimensions: 6"H x 11"W x 14"L WT: 9 lbs UPC: 031669061200

Read more less

BEP Pro Installer Terminal Block - 6 Way - 30AThis terminal block is ideal for isolated connections up to 30A and suitable for connecting tails from AC and DC panels.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Heavy Duty Lug 2GA Wire 1/2" Post *10-PackAncor Marine Grade lugs are manufactured from 100 percent heavy-duty annealed tinned copper, providing maximum current flow while resisting corrosion from salt and moisture. The seamless barrel design allows for maximum strength when crimped. Closed-end design seals out moisture so cables stay dry and corrosion free.Specifications: 100% Tinned Copper UL 486A Specifications: Gauge: 2 AWG Heat Shrink: No Package Qty: 10 Post Size: 1/2" Type: Lugs Box Dimensions: 1"H x 3"W x 5"L WT: 0.3 lbs UPC: 091887244083

Read more less

90° Tinned Copper Lug #1 - 5/16" - 2-Piece90° bend for ease of wire routing. Specifications: Type: Lugs Post Size: 5/16" Package Qty: 2 Heat Shrink: No Gauge: 1 AWG Box Dimensions: 1"H x 1"W x 3"L WT: 0.2 lbs UPC: 091887991697

Read more less

Yellow 18 AWG Tinned Copper Wire - 100'Ancor Marine Grade wire products are the longest lasting and most rugged available, exceeding UL 1426, ABYC and US Coast Guard Charter boat (CFR Title 46) standards. They are constructed with premium vinyl insulation that is rated at 600V, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. Highest quality ultra flexible (Type 3) tinned copper stranding provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. Wire Gauge: 18 AWG Nominal O.D. (inches): 7/64 Nominal O.D. (mm): 3 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Yellow Length (Feet): 100' Gauge: 18 AWG Box Dimensions: 3"H x 3"W x 4"L WT: 1.1 lbs UPC: 091887102109

Read more less

BM50 Male Inlet Parts KitThis SmartPlug service kit provides electrical components, hardware and gaskets.  Compatible With:BM50 SmartPlug Features: Ease of Use – Easily replaces missing or damaged pieces Interchangeable with SmartPlug Connectors *Sold as an IndividualWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATO/ATC Fuse Pack - 7.5 Amp - 25-PackFeatures: Fast-acting type fuses ideal for electronic devices Standard circuit protection device for automobiles and trucks Tin-plated connector blades for corrosion resistance Specifications: Amperage: 7.5 Amp Maximum Voltage: 32V DC Interrupt Capacity: 1000A WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 7.5a Fuse Type: ATO/ATC Type: Fuses Box Dimensions: 2"H x 2"W x 4"L WT: 0.1 lbs UPC: 632085524012

Read more less

easyID Fuse 20 AmpeasyID™ illuminated ATC® blade fuses use Light Emitting Diode (LED) technology to show that a fuse has blown, making them easy to spot in fuse panels tucked up under dark dashboards. Replaces non illuminating ATO® or ATC® fuses Fast acting Two per retail package SpecificationsAmperage; 20AInterrupt Capacity: 1000A @ 32V DCBlade Material: tin-platedWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 20a Fuse Type: ATO/ATC Type: Fuses Box Dimensions: 1"H x 1"W x 3"L WT: 0.1 lbs UPC: 632085052966 Brochure (pdf)

Read more less

SPST Contura Switch - OFF/(ON)Single pole, single throw switch turns one circuit on and off. Common application includes intermittent horn or windshield wiper control. Contura switches are rated to IP66, high-pressure wash resistant. Recommended for replacements in waterproof electrical panels with rocker switches to ensure waterproof integrity. The black and gray switches and covers are interchangeable with similar switches used as original equipment on many common boat types.Features: Nominal voltage 12V/24V DC Rated for 20A at 12V DC, 15A at 24V DC 1/4" blade terminals Snap-in mounting to fit panel hole 1.45" x .83" into panels .093" to .187" thick Same as Cole Hersee part number 58332-20 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Throw/Pole: SPST Color: Black Action: (On)/Off Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 870216046419

Read more less

MasterBus Cable - 0.2M Suitable for data traffic and powering peripheral equipment, this is the only cable you need for your MasterBus network. MasterBus compatible products come standard with two ports, while other equipment requires an interface.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Insulated Distribution Stud, Single 1/4"Insulated Distribution Stud, Single 1/4" - Made with high temperature plastic bases Stud covers push securely over the threaded stud covering to ABYC standards Dual studs ideal for +ve / -ve connections, branch circuits, windlass or inverter installations Covers supplied with display versions WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

30A 125V CordsetEEL ShorePower CordsetsOne Hand. A simple twist. Full Power.The EEL (Easily Engaged Lock) ShorePower Cordset has an industry first, jaw-clamp design providing one-handed operation and a secure waterproof seal which completely eliminates the need for a locking ring. The EEL connection is built for the harshest environments and is UL approved. This easy-to-use cordset features a built-in cord light which serves as an alert to boaters when the cord is left plugged in. And, best of all, it works with your current inlet. In addition to cordsets with the EEL System, Marinco also has a full set of Pigtail and Y adapters all using the new EEL technology.Features: Designed for use with standard inlets (NEMA)30A, 125V capacities; 12' length Cord sets meet global industry standards including ABYC and UL New wing-clamp technology provides a true, watertight connection every time Single-handed operation Eliminates the need for a sealing ring Secondary locking feature for added security Built-in LED cord light guides you to a secure connection every time, even in the dark WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 30a Voltage: 125v Type: Cordset Length: 12' Box Dimensions: 3"H x 11"W x 11"L WT: 5.5 lbs UPC: 093344051630 Owner's Manual (pdf)

Read more less

Heavy Duty CB Module, 80A705 Contour Circuit Breaker HD allows switchable protection for heavy duty circuits like Windlasses or Davit winches utilizing Bussmann Heavy Duty thermal circuit breakers. Allows switchable protection for heavy duty circuits like windlasses or davit winches Modular sizing with contour lock molding allows easy grouping WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 80a Box Dimensions: 3"H x 4"W x 9"L WT: 0.6 lbs UPC: 870216010038

Read more less

12-10 Heatshrink Butt Connectors - 3-PackGuage Size: 12-10Quantity: 3Product Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC. Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief. Nylon insulator, preferred by experts, for Marine Grade resistance to sunlight, water, oil, chemicals, vibration and cut-through damage. UL Listed and CSA Recognized Highest shrink ratio - shrinks to 1/3 original size. Shrinks at 257 deg. F/125 deg. C. Operating temperature range 40 deg. C to 110 deg. C. ANCOR heat shrink connectors offer heat activated adhesive built into the sleeve of the heat shrink tubing Shrinks to form a water tight seal and the ultimate vibration and strain relief. Tinned for corrosion resistance. Pure copper for maximum current flow. Brazed seam for maximum strength. Wire range: 12-10 mm: 3-5 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Gauge: 12-10 AWG Package Qty: 3 Heat Shrink: Yes Type: Butt Connectors Box Dimensions: 1"H x 1"W x 1"L WT: 0.1 lbs UPC: 091887307986 Quick Guide (pdf)

Read more less

DT Deutsch Receptacle Repair Kit - 14-18 AWG (3 Position)Pacer's DT repair kits use the larger size 16 contacts (Deutsch Pin P/N 0460-215-16141, Socket P/N 0462-209-16141) for applications using 14 AWG wires. However, DT series connectors are designed for 18-14 wire gauge applications. The DT series offers electrical designers the ability to use multiple sizes of 16 contacts (18-14 AWG) each with a 13-amp continuous capacity, within a single shell. Pacer also sells these other components for use in a wider range of applications.Features: Packs include all parts needed to assemble a connector One to two extra terminals Cavity plugs to seal open circuits Applications: Wire-to-wire applications Enclosed connectors offer field-proven reliability and rugged quality Compliances: Ingress Protection (IP) Level: IP68 and IP6K9K EU RoHS/ELV Standard UL-94 Recognized Characteristics: Wedge locks ensure contact alignment and retention Redundant Silicone Seals Hand-insertable and removable contacts Technical Specifications: Number of Cavities: 3 Housing: Rectangular receptacle, plastic reinforced with glass fiber Contact Size: 16 (13 amp) Wire Size: 14 AWG Holds Pin/Socket: Pins Operating Temperature: -55°C to 125°C Contents:  (1) 3 pos. receptacle (1) 3 pos. wedge lock (4) pins (1) cavity plug Quick Guide (pdf)

Read more less

ProSportHD 8 Gen 4 - 8 Amp - 2 Bank Battery ChargerProSportHD Generation 4 boasts a tri-surface heatsink design. This heavy-duty lightweight design delivers significantly faster charging through optimal cooling, while delivering true rated amp output during charge mode. ProSportHD's enhanced microprocessor and software provides digital features including: fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators and three digitally selectable performance charge profiles for Flooded (lead acid), AGM and GEL batteries. HP AGM profile on ProSportHD 20 Dual only. Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real time installation and battery fault status. Designed for use in harsh environments with our industrial grade jacketed DC and AC power cables which include molded strain reliefs and wire splitters. Features: ProMar Digital Technology Microprocessor and software controlled charging technology for fast, precise charging Distributed-On-Demand™ Technology 100% of all available charging amps are utilized by distributing unused charging amps to any one or combination of all batteries as needed Heavy Duty Tri-Surface Extruded Heat Sink Design Upper, lower and rear facing heat sink design for optimal cooling while delivering true rated constant current charging amps during its two charge mode Expanded LED Display with Completion Status Gauge LED fuel gauge style completion status. Four color multi-stage mode LED status bar. Multi-stage Charge Mode, System Check OK, individual Battery Status and Battery Type indication Lightweight Design Up to 40% lighter compared to an epoxy filled charger Auto-Maintain Energy Saver Mode Monitor and auto maintain batteries only when needed to maintain full state of charge. This significantly reduces AC power consumption Fully Automatic 5-Stage Digital Performance Charging 5 Stages: Analyzes, charges, conditions, auto maintains and reconditions batteries once a month during storage periods. Fully charges and extends battery life Built-in Quality and Safety Dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage and ignition protection. Certified to Marine UL 1236. CEC and DOE listed. FCC Class B Easy Installation and Operation Pre-wired with 6’ AC and DC cables Battery Type: Group 24–31 Flooded, AGM, HP AGM and GEL batteries 3 Year Warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Portable: No Charging Banks: 2 Charger Output Voltage: 12/24v Charger Output - Amps: 8a Charger Input - Voltage: 120v Box Dimensions: 7"H x 9"W x 12"L WT: 6.05 lbs UPC: 031669440081

Read more less

DPDT Rocker Switch - 12V/24V - (ON)/OFF/(ON)Double pole, double throw switch turns two of four circuits on at a time.Features: Nominal voltage is 12V DC Rated for 25A at 12V DC Six 1/4" blade terminals Snap-in mounting to fit panel hole 1.45" x .83" into panels .093" to .187" thick Same as Cole Hersee part number 58027-11 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Throw/Pole: DPDT Color: Black Action: (On)/Off/(On) Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 870216046341

Read more less

22-18 Gauge - 3/8" Heat Shrink Ring Terminal - 25-PackWire Range:22-18Screw Size: 3/8"Quantity: 25Product Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Nylon insulator, preferred by experts, for Marine Grade™ resistance to sunlight, water, oil, chemicals, vibration and cut-through damage UL Listed and CSA Recognized Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257° F/125° C Operating temperature range 40° C to 110° C ANCOR heat shrink connectors offer heat activated adhesive built into the sleeve of the heat shrink tubing Shrinks to form a water tight seal and the ultimate vibration and strain relief Tinned for corrosion resistance Pure copper for maximum current flow Brazed seam for maximum strength WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Gauge: 22-18 AWG Package Qty: 25 Heat Shrink: Yes Type: Ring Terminals Post Size: 3/8" Box Dimensions: 1"H x 4"W x 4"L WT: 0.2 lbs UPC: 091887311150 Quick Guide (pdf)

Read more less

All Digital Electronic ChargingIndustry recognized with the 2010 IBEX Innovation Award, ProNauticP employs our ProMar Digital Performance Charging Platform which combines all digital control and software-based power conversion technology with global energy management features. ProNauticP addresses the trend of incorporating and using more 12-volt electronics on-board today's power, sail, cruising and sport fishing boats. Boasting twelve digitally-controlled performance charging profiles with finger tip selection, ProNauticP fully charges, conditions, maintains and re-conditions batteries while extending battery life and maximizing battery reserve power performance. ProNauticP is Power Factor Corrected with auto-ranging global AC input allowing all models to operate off a standard household power connection. Featuring dual digital displays for real-time display of actual charging voltage and amperage and AC power-on diagnostics with pass or fail status in addition to discreet fault indication for mis-wiring or adverse battery bank conditions. Designed to provide more time on the water enjoying what you like most... boating.ProMar Digital Performance ChargingProMar Digital Charging Performance - 12 Selectable ProfilesUp to 12 performance & precision 4-stage charging profiles: Charge, Condition, Maintain and Re-condition. Automatic dockside power mode for 12 Volt DC lighting and appliances. Factory set for Flooded (Lead Acid) batteries. AGM, GEL selectable.Power Factor Correction - Global AC InputAuto-ranging (100-250VAC/50-60Hz) global AC input with reduced harmonic distortion allowing all models to operate off a household power outlet connection. ProNauticP consumes less power so more AC power is available on board.Distributed On Demand TechnologyAutomatically senses and distributes 100% of available charging amps to any one bank or combination of all banks.Digital Self-Calculating Absorption and Battery Health Re-Conditioning ModeAutomatically programs conditioning time based on discharge state of batteries. Automatically de-sulfates batteries after 21 days in the maintain mode, improving reserve power performance & extending battery life.Conservation Energy Saver ModeAfter 72 hours of not seeing a load greater than 5 amps, float voltage will be lowered consuming less energy during storage periods. (for flooded & sealed charge profiles) Service and Fault Mode LED IndicatorsReal time indication of wiring faults or adverse conditions that may impact the operation of a boat's charging system.Automatic Fan Speed ControlQuiet operation. Innovative front exhaust prevents restriction of air flow and cooling.Automatic Temperature Compensation and Built-in SafetyRemote temperature probe included - Ignition protected and current limiting. Designed and constructed to: Marine ULc 1236, CE, CTick and FCC Class B.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 40a Charging Banks: 3 Portable: No Charger Input - Voltage: 120/240v Charger Output Voltage: 12v Box Dimensions: 6"H x 11"W x 13"L WT: 6.8 lbs UPC: 031669631403 Owner's Manual (pdf)Brochure (pdf)

Read more less

ProSafe FAILSAFE 60amp Galvanic IsolatorProSafe FS installs easily and does not require a dedicated monitor to verify the operational status of the galvanic isolator as required by non FailSafe Certified galvanic isolators.ProSafe FS 60 is built on robust FlatPack semiconductor platforms ensuring that in the event of a failure, the failure is safe by not compromising the ground continuity on-board when connected to AC Shore Power. ABYC A-28 July '08 Compliant and Fail Safe CertifiedCertified by Underwriters Laboratories (UL). Insures shore power safety ground wire is maintained through the isolator. Flat Pack High Power SemiconductorsRobust high power diodes allow the FS Series to meet the new FailSafe criteria for conducting inrush currents of 3,000 amps for the required duration period. Ignition ProtectedMeets ISO 8846 and can be mounted within an engine compartment. Gold Plated Terminations WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

Current Model Outboard Solenoid with Flat Isolated BaseThe outboard solenoid will fit the current model Mercruiser and Mercury. Isolated base, 12 Volt.Replaces:MERCURY 89-850189MERCURY 89-850189TMERCURY 89-91975MERCURY 89-96054MERCURY 89-96054T*ARCO Assurance 12-month part and labor warranty protectionThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Parts Box Dimensions: 3"H x 3"W x 4"L WT: 0.4 lbs UPC: 693006001616

Read more less

Tank Level Monitor Sender InterfaceThe 600-TLM-SIF signal converter module is used to convert from 10-180 ohm, or 240-33 ohm tank sender outputs, to a 0-5V output. BEP equipment that uses a 0-5 volt signal input includes the DCSM DC/Systems Monitor, CZone Digital Switching/Monitoring, and the 600-TLM tank monitor.

Read more less

5235ATO/ATC Fuse1A Fast-acting type fuse ideal for electronic devices Standard circuit protection device for automobiles and trucks Tin-plated connector blades for corrosion resistance Visible indication of blown condition Sold in packages of 2 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 1a Fuse Type: ATO/ATC Type: Fuses Box Dimensions: 1"H x 3"W x 5"L WT: 0.1 lbs UPC: 632085052355

Read more less

SPDT Rocker Switch - 2-LEDs - 12V/24V - ON/OFF/ONSingle pole, double throw switch turns one of two circuits on.Features: Includes two LEDs The nominal voltage is 12V DC Rated for 25A at12V DC Four 1/4" blade terminals Snap-in mounting to fit panel hole 1.45" x .83" into panels .093" to .187" thick Same as Cole Hersee part number 58327-06 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Throw/Pole: SPDT Color: Black Action: On/Off/On Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 870216046365

Read more less