DC 105 CFM Flangemount 3" BlowersJabsco blowers are primarily intended for intermittent duty cycles such as evacuating fuel vapors from bilge areas. If desired, they also may be used for other general air circulation applications with longer duty cycles. However, when doing so, it should be noted that the maximum motor life is approximately 1000 hours. Therefore, the blower should only be used for applications if this length of service is acceptable.Features: Tough Reinforced Plastic Housing Mount to any surface Slip-On Inlet and Outlet Ducting Connection Efficient High Volume Air Flow Low Current Draw Corrosion-Resistant Materials Throughout N.M.M.A. Type Accepted Meets USCG Regulation 183.410 and ISO 8846 MARINE for Ignition Protection Complies with ISO 9097 MARINE WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Ducting: 3" Open Flow (CFM): 105 CFM Volts: 12v Box Dimensions: 7"H x 8"W x 9"L WT: 2.6 lbs UPC: 1067188002973 Owner's Manual (pdf)

Read more less

Y-ValveThe Jabsco Y-Valve is designed to provide flexibility of onboard waste management by diverting waste either into an onboard holding tank or directly overboard where legal to do so. Check local and Federal regulations to determine where direct overboard discharge of untreated waste is permitted. No overboard discharge of untreated waste is allowed within three miles of shore.Some near shore areas and inland areas are designated as "No-Discharge Zones" where the discharge of any onboard waste, even treated waste is strictly prohibited. Many of these areas require a waste retention system that can be positively secured in an onboard retention mode. The Jabsco Y- Valve accommodates this requirement by providing the ability to add a padlock that secures the selector handle in either direction to ensure waste is directed to an onboard holding tank. The Y-Valve may also be used to direct waste from a holding tank to an onboard waste discharge pump for holding tank evacuation or, alternatively, to a waste deck plate for removal by a shoreside pump-out facility.The Y- Valve may also be used in a bilge pumping system to select between two separate bilge pickups in different bilge compartments providing for evacuation of two separate bilge areas with only one bilge pump.Features: Chemical and corrosion resistant polypropylene and stainless steel construction Selector lever can be padlocked (lock not included) and/or sealed in either position Ports can be rotated so discharge plumbing can be routed away in parallel, at 900 or in opposite directions, or either up or down without disassembly Valve is supplied with both 1-1/2" (38 mm) ports (fitted) and extra 1" (25 mm) straight inlet port Optional shaft extension allows valve to be mounted through a bulkhead up to 1-3/4" thick with only the selector handle exposed Self cleaning design provides trouble free operation Molded in flow direction indicator arrows Easy access to three sturdy mounting feet for quick and simple installation Easy access to valve by removal of just three hex head machine screws, top cover and diverter assembly lift away from the body WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Misc Box Dimensions: 5"H x 8"W x 8"L WT: 1.7 lbs UPC: 671880536462 Owner's Manual (pdf)

Read more less

Service KitJabsco Service Kit is for Manual 29090 and 29120 Series Toilets from 1998-2007.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 3"H x 6"W x 7"L WT: 0.4 lbs UPC: 671880524131

Read more less

Service Kit f/Manual Toilet 29090/29120-3000WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 2"H x 6"W x 9"L WT: 0.35 lbs UPC: 671880587921

Read more less

Accumulator TankThis Accumulator Tank is intended for installation in any pumped water system controlled by a pressure switch. For example, PAR-MATE 2.5 or any Jabsco pressure pumps as found in boats, RV's, motor caravans, coaches and similar applications.The Accumulator Tank smoothes water flow and reduces on/off cycling of the pump by lessening the variation in pressure and flow between the pump and the outlets in the system.The even flow of water gives better control of hot water temperature especially noticeable with instantaneous gas water heaters and with showers.The reduced on/off cycling reduces noise from the pump motor, and from shock pressures (pipe hammer). It also reduces battery drain, and gives longer pump life.Features: Internal Bladder Smoother and More Even Flow Quieter Water System Better Temperature Control Longer Pump life Lower battery Drain Simply fitted to new or existing systems Compact size Snap-in port fittings include both: 1/2" barbed hose fittings and 1/2" threaded hose fittings Tank: hygienic, light, compact, impact and pressure resistant plastic construction WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Accumulator/Pressure Tanks Box Dimensions: 5"H x 5"W x 15"L WT: 1.9 lbs UPC: 671880026819 Owner's Manual (pdf)

Read more less

Engine Oil Changer Oil Drain PumpPolished brass hand pump connects directly to engine oil dipstick tube on many popular marine engines such as OMC and Mercruiser.Features: Screws onto threaded male 3/4" garden hose (GHT) fitting on top of dipstick tube. Gives simple "one-hand" pumping Complete with 2ft of 1/2" ID drain hose WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

Read more less

Mini Accumulator TankPart #: 30573-0003This accumulator tank is intended for installation in any pumped water system controlled by a pressure switch, and may also be used with air-driven pumps. The tank can serve as a storage vessel as well as a pulsation dampener for pressurized fluid. The accumulator tank smoothes water flow and reduces on/off switch cycling of the pump by lessening the variation in pressure and flow between the pump and the system discharge points.The even flow of water gives better control of hot water temperature with systems using instant water heaters.Features: Internal bladder Smoother flow Quieter water system Longer pump life Easily fitted to new or existing systems Compact size Quick-connect/disconnect port flttings Mounting point for optional pressure switch Food grade materials, NSF Standard 18 listed Volume: 21.5 oz Dimensions: 8.4 x 4.7 inches Max Pressure: 125 psi Weight: 0.96 lb Pre charged pressure: 10 psiWARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Accumulator/Pressure Tanks Box Dimensions: 5"H x 8"W x 12"L WT: 1.35 lbs UPC: 671880582834 Brochure (pdf)

Read more less

Replacement Sealed Beam for 135SL SearchlightFeatures: 50 Watt light 3-1/2" x 6" bulb For 135SL Searchlight WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

Vented LoopVented loops are anti-siphon safety devices for use with both manual and electric marine toilets installed below the waterline (static or heeled).WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Vented Loops Box Dimensions: 2"H x 9"W x 10"L WT: 0.9 lbs UPC: 671880529501 Owner's Manual (pdf)

Read more less

Water Pressure Regulator - Flush Mount - Chrome - 45 psiDesigned for day and night protection of the entire plumbing system from unregulated city water system hook-ups. Whether connected to a dock-side main or a campground faucet, the Jabsco Regulator will maintain regulated output at low or high flow rates. The removable strainer protects valves and seals seats from pipe scale and other debris.Features: Water Pressure Regulators protect your boat's water system from the damaging pressures of unregulated city water hook-ups Reduces unregulated city water pressures that can run as high as 125 psi down to a safe 45 psi - automatically Built-in backflow preventer Federal and State required on RV's with water service hookup Includes GHT (Garden Hose Thread) fittings for potable garden hose connection

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:12Dimensions: Diameter:3-3/4" Shaft Width:1" Shaft Diameter:2-9/16" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Valve Kit VitonThe Jabsco's Valve Kit Viton is a check valve kit, Viton for a Jabsco diaphragm pump.

Read more less

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 3" W, 5/8" Shaft DiameterFeatures: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 3", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

JABSCO WATER PRESSURE REGULATORFLUSH MOUNT MODEL 44411-SERIESDesigned for day and night protection of the entire plumbing system fromunregulated city water system hook-ups. Whether connected to a dock-sidemain or a campground faucet, the new Jabsco Regulator will maintain regulatedoutput at low or high flow rates. The removable strainer protectsvalves and seal-seats from pipe scale and other debris.FEATURES Reduces unregulated city water pressures that can runas high as 125 psi down to a safe 45 psi - automatically Features built-in backflow preventer. Federal and Staterequired on RV's with water service hookup Flush mounts permanently in vessel super structure Easily replaces most original city water entries Automatic pressure regulation Built-in backflow preventer Easy cleaning strainer Dust cap WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)Brochure (pdf)

Read more less

Service Kit f/Electric Toilet 37010 SeriesIncludes: Joker Valve O-Ring Washer, Fiber Gasket Flexible Impeller Seal & Retainer WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 2"H x 7"W x 7"L WT: 0.4 lbs UPC: 671880032827

Read more less

58541-1000 Pulley & Belt Kit Kit contains small and Large pulley, belt and clip.Compatible With:58500 Series Lite Flush Toilets*Sold as an Individual  Specifications: Type: Service Kits Box Dimensions: 1"H x 4"W x 6"L WT: 0.5 lbs UPC: 671880616874

Read more less

JABSCO WATER PRESSURE REGULATORFLUSH MOUNT MODEL 44411-SERIESDesigned for day and night protection of the entire plumbing system fromunregulated city water system hook-ups. Whether connected to a dock-sidemain or a campground faucet, the new Jabsco Regulator will maintain regulatedoutput at low or high flow rates. The removable strainer protectsvalves and seal-seats from pipe scale and other debris.FEATURES Reduces unregulated city water pressures that can runas high as 125 psi down to a safe 45 psi - automatically Features built-in backflow preventer. Federal and Staterequired on RV's with water service hookup Flush mounts permanently in vessel super structure Easily replaces most original city water entries Automatic pressure regulation Built-in backflow preventer Easy cleaning strainer Dust cap Owner's Manual (pdf)Brochure (pdf)

Read more less

Little Pal Utility PumpCompact polished brass multi-purpose hand pump Ideal for small engine and gearbox oil drain Simply pump old oil out with dipstick probe Oil and corrosion resistant brass and neoprene construction with up to 1 gpm output Small enough to fit any tool box WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 1 GPM Outlet Size: 1/2" Type: Manual Box Dimensions: 2"H x 8"W x 11"L WT: 1 lbs UPC: 671880028622 Quick Guide (pdf)

Read more less

Vented LoopVented loops are anti-siphon safety devices for use with both manual and electric marine toilets installed below the waterline (static or heeled)WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Vented Loops Box Dimensions: 2"H x 9"W x 10"L WT: 0.5 lbs UPC: 671880529495 Owner's Manual (pdf)

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:12Dimensions: Diameter:2-1/4" Shaft Width:5/8" Shaft Diameter:1-29/32"Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller Kit - 9 Blade - Nitrile - 3-3/4" Diameter x 2-1/2" W, 1" Shaft DiamterFeatures: Material: Nitrile Drive Type: Single Flat Drive Number of Blades: 9 Dimensions: Diameter:3-3/4", Shaft Diameter:1", Shaft Width:2-1/2" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:9Dimensions: Diameter:3-3/4" Shaft Width:1" Shaft Diameter:2-1/2" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Water Pressure Regulator - Flush Mount - WhiteEasy to install, easy-clean in-line filter, permanently installed flush mount model and in-line model with brass garden hose fittings that connect dockside water entry and garden hose water hook-up. Reduce high water pressures (up to 100 psi down to 35 psi). Features: Built-in back flow preventer Easy-to-install Easy clean in-line filter

Read more less

JABSCO WATER PRESSURE REGULATORFLUSH MOUNT MODEL 44411-SERIESDesigned for day and night protection of the entire plumbing system fromunregulated city water system hook-ups. Whether connected to a dock-sidemain or a campground faucet, the new Jabsco Regulator will maintain regulatedoutput at low or high flow rates. The removable strainer protectsvalves and seal-seats from pipe scale and other debris.FEATURES Reduces unregulated city water pressures that can runas high as 125 psi down to a safe 45 psi - automatically Features built-in backflow preventer. Federal and Staterequired on RV's with water service hookup Flush mounts permanently in vessel super structure Easily replaces most original city water entries Automatic pressure regulation Built-in backflow preventer Easy cleaning strainer Dust cap WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)Brochure (pdf)

Read more less

Drill PumpsJabsco drill pumps provide a very versatile means of transferring fluid almost anywhere an electric drill with 1/4" to 3/8" chuck can be operated. They provide easy powered pumping almost anywhere a hand utility pump might be used. Pumps up to 3.5 gpm Self-priming to 3ft 1/4" diameter shaft Supplied with 3/4" garden hose thread port adapters WARNING: This product can expose you to chemicals including COBALT METAL POWDER which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 3.5 GPM Box Dimensions: 3"H x 6"W x 9"L WT: 0.7 lbs UPC: 671880012577 Quick Guide (pdf)

Read more less

Impeller Kit - 10 Blade - Neoprene - 2" Diameter x 7/8"W Pin Drive InsertMaterial: NeopreneInsert Material:BrassDrive Type: Slotted Shaft Pin Drive or Through Hole Pin DriveNumber of Blades: 10Dimensions:Diameter:2"Shaft Width:1/2"Shaft Diameter:7/8"Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Ballast King ImpellerFeatures: Replacement Impeller Fits Ballast King Jabsco is a worldwide leading manufacture of products for the leisure marine market including water system, engine cooling pumps, searchlights and marine waste systems. Jabsco also offers industrial pumps for hygienic applications, fluid transfer in chemical processing, laboratory, paint processing, plating, and construction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Brochure (pdf)

Read more less

Impeller KitMaterial:NitrileDrive Type:Single Flat DriveNumber of Blades:10Dimensions: Diameter:1-19/32" Shaft Width:5/16" Shaft Diameter:3/4" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Flush Mount Hose AdapterPerfect solution to remove that unsightly hose bib deck fitting and rusty knob. This will enable you to connect your water hose in seconds.Enables you to quick-connect your water hose in seconds. Position this fitting close to your anchor windlass to clean muddy anchors, or locate one on each side of your vessel to make cleanups much easier. Combine the deck washdown fitting with a hose coil washdown hose and keep the deck clutter free.Features: Extra 3/4" GHT male hose adaptor suitable for HoseCoil Water flow available with an easy twist of the fitting Easy to install Position this fitting close to your anchor windlass to clean those muddy anchors. Or locate one on each side of your vessel to make those cleanups much easier Just combine the Quick Release Deck Washdown fitting with a Hose Coil Washdown hose and a high volume Jabsco PAR-Max 4 Washdown pump to keep the deck clutter free Comes with a pre-installed check valve that connects your hose with a simple twist to the deck fitting, even under full pressure Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 8"W x 8"L WT: 0.3 lbs UPC: 671880550253

Read more less

Impeller KitMaterial:UrethaneDrive Type:Single Flat DriveNumber of Blades:6Dimensions: Diameter:2" Shaft Width:7/8" Shaft Diameter:5/16" Insert Material:PlasticJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:10Dimensions:Diameter:2-1/4"Shaft Width:5/8"Shaft Diameter:2Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Vented LoopVented loops are anti-siphon safety devices for use with both manual and electric marine toilets installed below the waterline (static or heeled)WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Vented Loops Box Dimensions: 1"H x 6"W x 7"L WT: 0.1 lbs UPC: 671880529488 Owner's Manual (pdf)

Read more less

Service Kit for 50880 Series PumpsFeatures: Contains - 2 Joker Valves, Diaphragm, and Ports For the 50880 Series Includes Service Instructions Actual Weight: 0.13 kg (Approximately 0.33 kg packed)

Read more less

Service Kit for 50890 Series PumpThe Jabsco SK890 Waste Pump Service Kit is designed for rebuilding the Jabsco 50890 Single Diaphragm Design.Kit Includes: (1) Cover #7 (1) Diaphragm #8 (4) Hex Head Screws #10 (1) Recessed Pan Head Screw #12 (1) Washer #14 (2) Pump Joker Valves #16 (2) Pump Ports #17 WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Key DriveNumber of Blades:12Dimensions:Diameter:2-7/16"Shaft Width:5/8"Shaft Diameter:1-1/4Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller Kit - 8 Blade - Nitrile - 2-9/16" Diameter - Spline DriveMaterial: NitrileDrive Type: Single Flat DriveNumber of Blades: 8Dimensions:Diameter: 2-9/16"Shaft Width: 5/8"Shaft Diameter: 2"Insert Material: BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NitrileDrive Type:Single Flat DriveNumber of Blades:8Dimensions:Diameter:1-1/4"Shaft Width:5/16"Shaft Diameter:15/32"Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 2" W, 5/8" ShaftDiameterFeatures: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 2", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:10Dimensions: Diameter:2-9/16" Shaft Width:⅝" Shaft Diameter:2" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:12Dimensions: Diameter:2-1/4" Shaft Width:1-1/4" Shaft Diameter:5/8"Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

18916-0040 Replacement Pressure Switch - 40 PSICompatible Series: 31595-Series 31600-Series 31620-Series 31630-Series WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

Pressure Switch - 50 PSIThe Jabsco 18916-0050 is a pressure switch for a Jabsco diaphragm pump.WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

Quick Connect Trigger NozzleFeatures: Multiple flow control settings Quick connect hose/trigger nozzle Can work with both fresh and saltwater Designed for use with washdown pumps

Read more less

Valve Kit EPDMThe Jabsco's Valve Kit EPDM is a check valve kit, EPDM for a Jabsco diaphragm pump.

Read more less

Through Deck Kit for Manual Bilge PumpsFeatures:Actual Weight: 0.16 Kg  (Approx. 0.36 Kg packed)

Read more less

Motor Cover for 37010 SeriesJabsco's Motor Cover for 37010 Series Electric ToiletsWARNING: This product can expose you to chemicals including Vinyl Chloride which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

In-Line Non-Return Check Valve - 1-1/2"In-line non-return valve. Connections for 38mm (1½”) bore hose. Features: Connections: - for 38mm (1½”) bore hose Dimensions: - 108mm long, 55mm wide, 50mm high (in-line configuration) Aids pump priming, prevents backflow from pump into bilge Fits into pump suction line Robust plastic construction with nitrile rubber valve Adjustable port configuration for convenient hose angle Actual Weight: 0.11 Kg  (Approx. 0.31 Kg packed) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less