Service Kit for 50890 Series PumpThe Jabsco SK890 Waste Pump Service Kit is designed for rebuilding the Jabsco 50890 Single Diaphragm Design.Kit Includes: (1) Cover #7 (1) Diaphragm #8 (4) Hex Head Screws #10 (1) Recessed Pan Head Screw #12 (1) Washer #14 (2) Pump Joker Valves #16 (2) Pump Ports #17 WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

Viton Valve Kit Chamber Sub-AssemblyFKM check valve kit for the Triplex (triangle head)

Read more less

Discharge Pump Repair Kit for Marine Elegance & Atlantes Freedom Vortex Vac ToiletsKit Includes: 1 Motor Shaft Seal 31-102P 1 O-ring 221105 1 ME: Joker Valve 221135 1 ME: Joker Valve Insert 221146 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 085462025242

Read more less

Drain Plug with O-Ring for ARG Strainers 2008 & OlderDrain Plug before 080101 for ARG Strainers 2008 & Older

Read more less

ARG-1 Strainer Service KitARG Series raw water strainer service kit.Compatible with the Groco ARG 500, 750 and 755 series strainers.In the Box: (1) - 2-153 - Sight Glass O-Ring (1) - 2-135 - Cap O-Ring (1) - 2-228 - Cap O-Ring (4) - PFW-2 Set - Sight Glass Bolt Washer (1) - 2-011 - Drain Plug O-ring Before 08/01/01 (1) - 2-111 - Drain Plug O-ring After 08/01/01 *Sold as an Individual Specifications: Type: Service Kits Box Dimensions: 1"H x 4"W x 6"L WT: 0.1 lbs UPC: 742985010413 Owner's Manual (pdf)

Read more less

Smart Toilet Control Circuit BoardSmart Toilet Control (STC) is a controller for flushing toilets to optimize water use without compromising the quality of flush.Control consists of a controller, panel, and 7’ of cable. STC is designed to automatically start a flushing cycle if normal or water-saver buttons are pressed.The water-only button brings inlet water to the bowl when pressed and the empty-only button evacuates the bowl. Both water-only and empty buttons have a time limit of eight seconds.Flush timing of initial fill, discharge, and final fill are fully programmable from the panel. If wired, the panel also shows the holding tank's full status. When holding the tank full the LED is lit, and normal and water saver buttons are disabled. Water only and the empty button continues to function. Control is reverse polarity protected. In the case of reverse polarity motors and solenoids will activate as soon as power is connected. After reverse polarity is corrected (within 10 minutes), the unit will work as normal.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Atlantes Freedom Discharge ConversionThis discharge conversion allows users of the older Atlantes style macerators to upgrade to the newest style macerator offered by Raritan.The new macerator has proven to be extremely robust and was built with reliability and ease of service in mind. Even the best macerators occasionally have something thrown into them that should not be there. This macerator can often pass foreign objects but if not, this design will make accessing and working on the macerator much easier than the older style.The retrofit is fairly straight forward but you will need to know what model you previously owned to be certain that you get all the necessary pieces to make the transition from old to new.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Elbow Sprayer - Handle Pull Out - White with 6' Hose  This standard elbow sprayer is as reliable as it is functional.Features: White sprayer with a 6 ft. white nylon hose The included counter-top holder leaves the sprayer in a ready-for-action position The sprayer handle features a trigger sprayer for on/off control or a flip-up lock for continuous water flow Specifications: Water Connection: 3/8 in. BSP-F fitting Material: Glass reinforced plastic sprayer with nylon or chrome plated brass hose Mounting Hole: 1-1/16 in. Shipping Weight: 4 lbs. *The "P" within the part number indicates retail packaging

Read more less

Straight Handle Pull Out Sprayer - White with 6' HoseThis straight-handled sprayer is as reliable as it is functional.Features: White sprayer with 6 ft. white nylon hose Included counter-top holder leaves the sprayer in a ready-for-action position Sprayer handle features a trigger sprayer for on/off control or a flip-up lock for continuous water flow Specifications: Water Connection: 3/8 in. BSP-F fitting Material: Glass reinforced plastic sprayer with nylon or chrome plated brass hose Mounting Hole: 1-1/16 in. Shipping Weight: 4 lbs. *The "P" within the part number indicates retail packaging

Read more less

Grey Waste Tank Lid Replacement with SensorThe Grey Waste Tank enables the user to manage all grey waste on board easily, through one skin fitting. The Intelligent Control sensor integrated into the tank lid provides automatic operation of the grey waste pump. The sensor will detect water in the grey waste tank at a pre-determined level, and will automatically activate the grey waste pump. When the tank is emptied, the switch will automatically turn the grey waste pump off . The 2 sensor models include a second sensor which can be used to control a second grey waste pump. It is factory set to activate at a higher water level and will provide additional pumping capacity during periods of high infl ow to the grey waste tank. Alternatively, the second sensor can be wired to a high level alarm, warning of a high water level within the grey waste tank. The Grey Waste Tank is designed to collect grey shower waste water. If it is intended for use for any other purpose or with any other liquid, it is the user’s responsibility to ensure that the tank and switch are suitable for the intended use and, in particular, that the materials are fully compatible with the liquids to be used. The integrated Intelligent Control sensor is designed to operate at 12V d.c or 24V d.c. only. The sensor is suitable for use with pumps operating with current up to 20A, and is recommended for use with Whale Gulper® 220 or Gulper® 320 grey waste pumps.

Read more less

DC Driven Circulation Pump with Brushless Motor - BL30CM 12VThis circulation pump is for the circulation of water/antifreeze in heating or cooling systems on boats, buses, motor homes, and commercial vehicles. There are many advantages to this pump, such as its small size with high efficiency, maintenance-free, ceramic shaft, carbon fiber sleeve, completely waterproof (IP68), brushless DC control, and long service life.Features:  Motor brush-less magnetic isolated design For continuous duty Life span: 20,000 hours Materials of pump housing: ABS, PES/SPS/PA66 Motor IP classification: IP 68 Noise class: 35dB The max liquid temperature for continuous Duty is 80°C & Intermittent is 100°C Specifications: Port size: (inch) 3/4" / (mm) 20 Weight: 0.48 kg Capacity at 0.1 bar: 32 l/min  Capacity at 0.25 bar: 28 l/min Max load: 4.5A Max power consumption: 55W *Includes pump and motor Specifications: Type: Pumps/Drives Box Dimensions: 5"H x 5"W x 6"L WT: 1.6 lbs UPC: 7340176606907

Read more less

Active Carbon FilterPrevents outside odor coming from tank by connecting it at the highest point along the breather hose.Specifications: Weight: 0.15 kg/.25 lbs Type: Black water Adjustable Ports: With 16, 19, & 25mm / (3/8″, 3/4″, 1″)  *Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance

Read more less

316 SS Non-Perforated Worm Gear Hose Clamp - 3/8" Band - 11/32"-25/32" Clamping Range - 10-Pack - SAE Size 6Premium Marine Grade, all AISI 316 (high tensile strength) Stainless Steel Compact “HD NON-PERF” Worm Gear Hose Clamp. The 9.7 mm (0.382”) wide band is Non-Perforated and smooth on the inside with rolled edges. This eliminates hose damage with increased clamping force. The high strength, compact, one-piece 14mm (0.55”) wide housing provides one of the highest clamping force ratings of any worm gear style clamp.Features: The screw head is 7mm Long service life and safety for most general-purpose hose applications and connections Recommendations: Measure hose O.D. before selecting clamp size for proper fit Double clamp on each hose end for critical applications Construction: Band & Housing: 316 Stainless Steel 9.7 mm wide band – 0.8mm thick Screw Drive: 316 Stainless Steel 7.0 mm screw head Specifications: SAE Size: 6 Hose Inner Diameter: (inch) 5/16" - 3/8" Clamping Range: (inch) 11/32" – 25/32" / (mm) 13-20 Recommended Torque Inch lbs: 25-35 Quick Guide (pdf)

Read more less

Upper Assembly Replacement for 4248/4258 Series Pro Blaster II Deluxe 4.0/5.0 Washdown PumpsThis Shurflo upper assembly replacement is for the 4248/4258 Series Pro Blaster II Deluxe 4.0/5.0 washdown pumps listed below: Shurflo Pro Blaster II Deluxe 4.0 (4248-153-A09 [4248-153-E09]) Shurflo Pro Blaster II Deluxe 4.0 24 VDC (4248-163-A09 [4248-163-E09]) Shurflo Pro Blaster II Ultimate 5.0 (4258-153-A09 [4258-153-E09]) Shurflo Pro Blaster II Ultimate 5.0 24 VDC (4258-163-A09 [4258-163-E09]) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Automatic Switch AS888For full automatic bilge pumping operation, connect the automatic switch to your bilge pump. The AS888 automatic switch has a time-proven micro switch without mercury. When water exceeds the acceptable level, the pump is turned on by a rolling steel ball, which changes the pressure on the micro switch. The AS888 attaches to any SPX Johnson Pump Marine bilge pump through the clip on "T-slot" and can be used with 6, 12, 24 or 32 V systems. Use AS888 for a better and safer life afloat!

Read more less

Crown Head™ Deep Draft Repair KitThe Deep Draft Crown Head was last made in 1990 but some still exist out in the field today. While many of the parts are similar to today’s Crown Head there are some that are no longer available. For this reason we now include the macerator retro-fit for the old Deep Draft units to make the Centrifugal Discharge series.This repair kit will update the older style Deep Draft toilets to the new CD series. For those not wishing to tear apart units, Raritan still offers a Crown Head Exchange program that allows users to swap their old base for a new one at a reduced cost over buying new.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 3"H x 4"W x 7"L WT: 0.55 lbs UPC: 085462005749 Owner's Manual (pdf)

Read more less

Seat Lid & Seat for 960 Series Portable Toilet - PlatinumReplacement seat and lid for 960 Series toilets.Features:Color - Platinum*Sold as an IndividualWARNING: This product can expose you to chemicals including ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Parts Box Dimensions: 1"H x 15"W x 15"L WT: 1 lbs UPC: 713814067649

Read more less

Pressure Reducing City Water Entry - In-Line - CreamThis combination pressure reducing city water entry and check valve diaphragm design prevents high-pressure damage often caused by city water systems. This high performance water entry limits water pressure safely to 50 PSI while meeting or surpassing all check valve code requirements. This in-line pressure reducing water entry includes a check valve. 3/4" GSH Female swivel inlet. 1/2" NPSM - Male Outlet.Features: Small size, easy installation Continuous protection from high pressure surges Hose mounting eliminates need for permanent installation Fits standard 3/4" hose fittings Built-in check valve 50 PSI This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Thru-Hull Nut Aerator - Straight/90°Specifications: Thru-Hull Straight/90° Nut Aerator

Read more less

Washdown Water Outlet - Chrome Plated BrassEdit TitleThe Washdown Water Outlet allows for a garden hose to be hooked up to the onboard water system. Standard male hose connector. Requires a separate ball or gate valve to regulate water flow. Specifications: Pipe size: 1/2" FIPT x 3/4" MGHT Constructed of chrome-plated brass

Read more less

Stainless Hold-Down BracketStainless hold-down bracket for low-profile bilge water pickups. BRACKETS ARE NOT INCLUDED WITH BILGE-B-DRY ORDERS. If needed, use the stainless hold-down bracket to help secure your low-profile bilge water pickup.Specifications: Dimensions (inches): Rectangular Pickup: 0.98 H x 2.4 W x 3.9 L Dimensions (mm): Rectangular Pickup: 50 H x 60 W x 100 L

Read more less

MF 840 Vented Loop - 1-1/2"Installing one of our vented loops will ensure that fluids will not siphon from tank to tank. Vented loops are commonly used in the marine toilet system and engine cooling system. The simple valve system incorporated in the top of the loop allows air to enter the line when not in use, yet effectively seals as water or other fluid passes through. Molded in Marelon, neither vent nor loop will corrode. The duckbill one way valve is designed to seal properly if particulate matter is present in fluids. Specifications: Barb Size: 1-1/2" (38.1mm) Height: 5-1/4" (133.35mm) Width: 7-3/4" (196.85mm) Specifications: Type: Vented Loops Box Dimensions: 2"H x 5"W x 8"L WT: 0.45 lbs UPC: 028026148711

Read more less

15' 8 Pin ECU Display Cable for Passport I/O DisplayThis display cable is an 8-conductor, shielded cable with reversed RJ-45 modular plugs on each end.   This cable is compatible with Dometic 8-Pin Controls.Legacy # 222103008Features: 15' in length RJ-45 Connectors *Sold as an IndividualWARNING: This product can expose you to chemicals including ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Cables Box Dimensions: 1"H x 8"W x 8"L WT: 0.8 lbs UPC: 7315091425919

Read more less

Sea Era Discharge Repair KitRaritan's Discharge Repair Kit is specifically for the Raritan Sea Era.Raritan manufactures equipment for pleasure boats throughout the world. Products include marine toilets, waste treatment systems, icemakers and water heaters. Committed to the environment and preserving sea life, Raritan designs products to help maintain an environmental balance and ensure the quality of marine waters.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 3"H x 4"W x 7"L WT: 0.25 lbs UPC: 085462017216

Read more less

2-Gallon Salt Feed SystemThe LectraSan® does not require a salt feed system for ocean water use as the salinity of the ocean water is sufficient to operate the system as designed. Salt can be added to the LectraSan® using a 2-Gallon Salt Feed Tank for brackish water. Low salt is indicated on the LectraSan® Control Indicator Panel.OperationA salt solution is mixed and placed in the salt feed tank. Every time the toilet is flushed, part of the salt water solution is mixed with incoming water to increase the water salinity in the Treatment Tank. The LectraSan® Control Indicator Panel will show when the Salt Feed Tank needs to be refilled with more salt solution.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Parts Box Dimensions: 9"H x 10"W x 17"L WT: 2.85 lbs UPC: 085462002038 Owner's Manual (pdf)

Read more less

White Vertical Cup & Cap for Scandvik Part Number 1075This is a white replacement cap and cup for the vertically mounted recessed showers. This part is a kit (one #10030 cap and one #10031 cup).Features: These showers are typically mounted on the side of a center console or any vertical surface You can distinguish the vertically mounted unit by the Scandvik logo on the cap Specifications:Mounting Hole: 2-1/4 in.*The "P" within the part number indicates retail packaging

Read more less

White Container & Cap for Scandvik Part Numbers 10055,10275,10298, & 10826This is a replacement cap and cup for horizontally mounted recessed showers. Horizontally mounted showers can be distinguished by the shower on the cap. This specific model is a kit (one #10252 cap and one #10253 cup).Note: Pull-out shower/sprayer handle uses cups #10253 (white) or #10264 (black) and a white cap #10252 or a black cap #10263 Mixer valves use the white cup #10335 and the same white cap, #10252 *The "P" within the part number indicates retail packaging

Read more less

Recessed Shower with 6' White Hose - Push-ButtonThis part is part of the fifth generation of Scandvik recessed showers. Also, this recessed shower has an easy-to-use push-button.Features: White handle, cup, and cap with a 6 ft. white hose Improved UV protection and a better water seal when the cap is closed Built-in grab ring for easy deployment Mounts vertically or horizontally Mounting hardware is included Specifications: Water connection: 3/8 in. BSP-F threaded fitting Material: ABS and chrome-plated brass (push-button) Mounting Hole: 2-3/4 in. Shipping Weight: 4 lbs. *The "P" within the part number indicates retail packaging

Read more less

Ceramic Family Tap with Folding Spout - Chrome FinishFolding cold water tap with a high-reach swivel and folding spout. This particular part has a chrome finish.Specifications: Water Connection (inch): 3/8" BSP-M threaded shaft (1/2" NPS-M adapters included) Material: Solid brass with a chrome finish Mounting Hole (inch): 5/8" Shipping Weight: 3 lbs. *The "P" within the part number indicates retail packaging

Read more less

Replacement White Cup & Cap for Recessed ShowerThis recessed cap and cup design is made with Dupont™ Zytel® Nylon Resin for greater strength and UV exposure resistance. A rubber gasket under the cap will keep water out when the cap is closed. Features: Requires a 2-3/4 in. mounting hole.    Single white cap and cup NOTE: If you currently have a Scandvik recessed shower with a rubber cap, this latest design version will NOT fit your hole size. You will need to enlarge your current 2 1/4-in. hole to a larger 2 3/4-in.*The "P" within the part number indicates retail packaging

Read more less

Ceramic Angled Washdown Valve - Stainless Steel SpigotThis part is an angled washdown with a 316 Stainless Steel spigot.Features: Mounts easily with 3 #6 screws to the bulkhead 1/4 turn ceramic valve. Standard 3/4 in. garden hose thread for hose attachment Includes interchangeable fresh and raw pendant Specifications: Water Connection: 1/2 in. NPT-F Flange Diameter: 2-3/8 in. Shipping Weight: 2 lbs. *The "P" within the part number indicates retail packaging

Read more less

EvoFlex Drinking Water Hose - 4'Camco’s Evo Flex 4-Foot Drinking Water Hose with 5/8-inch ID is ideal for RV and marine use. Its extra flexible construction holds no memory, making it easier to position and store. Features nickel-plated machined fittings. Drinking water safe with a lead-free, BPA-free and phthalate-free formulation. The hose leaves no strong plastic taste in your water. UV-stabilized for a long life. Made in the USA.Features: Extra Flexible Design: Holds no memory, making it easier to position and store The Perfect Size Hose: 4-foot hose with 5/8-inch ID Drinking Water Safe: Contains a BPA-free, lead-free and phthalate-free formulation Provides Great Tasting Water: The hose won't leave a strong plastic taste in your water Durable Construction: Features nickel-plated machined fittings; UV-Stabilized: For a long life Made in the USA: Product is proudly made in the USA

Read more less

EVO Marine Water FilterCamco’s EVO Marine Water Filter offers protection against bad taste, odors, sediment, bacteria, chlorine, and other contaminants from your boat's freshwater supply. The result is fresh, clean, great-tasting water with a high flow straight from your tap. This filter is compatible with standard 2 ½-inch x 10-inch filter cartridges. The product includes a water filter canister, 5.0-micron sediment cartridge containing GAC (Granular Activated Carbon) and KDF, stainless steel mounting bracket, standard water hose fittings, 1/2-inch, and 5/8-inch hose barb fittings, spanner wrench, and an extension hose. This product includes standard water hose fittings as well as ½-inch and 5/8-inch barb fittings to allow you to choose between a water hose hookup or a direct plumb-in.Features: Premium Marine Water Filtration: Protects against bad taste, odors, sediment, bacteria, chlorine, and other contaminants from your boat's freshwater supply Provides Great Tasting Drinking Water: Offers fresh, clean, great-tasting water straight from your boat's tap High Flow Rate: Provides high water flow throughout your boat Compatibility: Fits standard 2 ½-inch x 10-inch filter cartridges Includes: Water filter canister, 5.0-micron sediment cartridge containing GAC (Granular Activated Carbon) and KDF, stainless steel mounting bracket, standard water hose fittings, ½ inch and 5/8-inch hose barb fittings, spanner wrench, and an extension hose Multiple Hookup Options: This product includes standard water hose fittings as well as ½-inch and 5/8-inch barb fittings to allow you to choose between a water hose hookup or a direct plumb-in

Read more less

MF 842 Vented Loop - 3/4"Installing one of our vented loops will ensure that fluids will not siphon from tank to tank. Vented loops are commonly used in the marine toilet system and engine cooling system. The simple valve system incorporated in the top of the loop allows air to enter the line when not in use, yet effectively seals as water or other fluid passes through. Molded in Marelon, neither vent nor loop will corrode. The duckbill one way valve is designed to seal properly if particulate matter is present in fluids. Specifications: Barb Size: 3/4" (19.05mm) Height: 4-1/2" (114.3mm) Width: 3-3/4"" (95.25mm) Specifications: Type: Vented Loops Box Dimensions: 2"H x 4"W x 5"L WT: 0.1 lbs UPC: 028026148728

Read more less

PUREWATER+All-In-One Water Filtration System 5 Micron Replacement FilterFeatures: Simple filter change by twisting off faucet head simply dropping filter into cartridge without crawling under sink On-demand ultra-clean tasting water from your tank Elegantly styled Simple to install Compact filter housing maximizes under sink storage

Read more less

IC Adapter Cable for Old IC Pumps to New IC AccessoriesThe Whale IC adaptor AK7690 allows old Gulper IC pumps to connect to new Whale IC accessories, such as strainers, gulleys, and manifolds.

Read more less

Heating Element with GasketThe WH1A-S is a screw in heating element that is 1250w at 120v designed to quickly and efficiently heat the water via electricity in a Raritan water heater. These elements must be installed, and the tank filled prior to applying any power or they will burn out. Raritan does offer an element that can last a bit longer if power is applied without water in the tank.Features: Includes Gasket Screw-In Type 120v WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Parts Box Dimensions: 2"H x 7"W x 8"L WT: 0.5 lbs UPC: 085462011269

Read more less

Pressure Reducing City Water Entry - Wall Mount - Gel WhiteThis combination pressure reducing city water entry and check valve diaphragm design prevents high-pressure damage often caused by city water systems. This high performance water entry limits water pressure safely to 50 PSI while meeting or surpassing all check valve code requirements. This in-line pressure reducing water entry includes a check valve. 3/4" GSH Female swivel inlet. 1/2" NPSM - Male Outlet.Features: Quick, Permanent Wall Mount Continuous protection from high pressure surges Fits standard hose fittings Built-in check valve 65 PSI This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Nano Touch Solenoid Invensys Kit - 12VThetford's Solenoid Invensys Kit is for use with Thetford's Touch SFT Kits.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Scupper Flapper Repair KitThe flapper scupper repair kit should take care of any flapper replacement job.  The traditional flapper scuppers use molded rubber flappers that curl and deform over time, requiring replacement to prevent leaking.  Our flappers are not rubber, but are molded of a thermoplastic elastomer that is resistant to UV and the elements, so they do not curl like the rubber flappers.Repairs most scuppers with flappers, regardless of manufacturer.Kit Contains: All parts needed to repair 2 scuppers of a given size.  Each kit contains 2 each of: 1-5/8" flappers, 1-7/8" flappers, and all necessary keepers and fasteners.

Read more less

Slinger Kit *3-PackJabsco toilet slinger.

Read more less

4 Gallon Salt Feed Tank with 12V PumpThe Four Gallon Salt Feed System with Pump is designed for boats that operate in fresh or brackish water and can only be used with the Lectra/San® MC™ or electro-scan™ Type I MSDs. The unit’s Control Panel monitors salinity and salt solution will automatically be added to the MSD when needed. Pressurized freshwater is required—a minimum of 15 psi (103 kPa) working pressure.The simple and basic operation of the system is as follows: the system needs salt water to operate properly and salt can be added when not in full seawater conditions. When the system is activated the electrical charge applied to the patented plates generates the disinfectant to kill viruses and bacteria. As that disinfectant is generated the high-speed macerator breaks apart the waste allowing greater contact between waste and disinfectant.  If your toilet uses freshwater we recommend considering the Purasan. Specifications: Type: Holding Tanks Box Dimensions: 11"H x 11"W x 18"L WT: 6.3 lbs UPC: 085462044687

Read more less

KlickTite 2 x 90 - 3/4" HoseAllows draining of the system quickly and effortlessly. 

Read more less

Solenoid Valve - 24V24V electric valve to be used with centralized fresh water system. Features:Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance 

Read more less

Raw Water System Eco Kit with Rocker Switch, Wire Harness & Fitting12V Raw Water Flush Kit is specifically designed for EasyFit, Nano, and Compass Eco Toilet models. This kit is essential for vessels that already have a pressurized raw water system onboard, providing an efficient raw water flushing solution without the need for a pump (if a pump is needed, refer to Thetford part number T-PF.P27 for 12V applications and T-PF.P28 for 24V applications). It's a perfect choice for those who wish to conserve fresh water on their boat.Features: Compatible with EasyFit, Nano, and Compass eco toilets Includes wall-mounted flush control switch Included 12' wire harness

Read more less

Freshwater Solenoid Kit for Nano Toilets - 12VFeatures: Allows use of onboard pressurized freshwater system and freshwater pump to be used for flushing function Compatible with Tecma Nano, Compass ECO ,and EasyFit compact macerating toilets Compact ECO rocker switch controls water inlet and outlet with reduced power and water consumption (UP to add water, DOWN to flush)

Read more less

4-Blade Chopper Kit with Lock Nut for 18590 Series Macerator PumpsThe Jabsco 4-Blade Chopper Kit replaces a worn, broken, or malfunctioning macerator chopper in the 18590 Series. The chopper is designed with 4 heads, each with its own blade to break up large debris before it enters the pump and other fluid lines. Includes a lock nut to secure it in place.

Read more less

Seal Kit for Quiet Flush ToiletsA replacement seal and retainer for Jabsco pumps and heads.

Read more less