Navico 9-Pin Mix & Match Chirp Cable - 1MAirmar's 9-Pin Mix & Match Chirp Cable for Navico Med and High or Highwide TransducersFeatures: Length: 1M 9-Pin for Med, High, and Highwide Transducers, Single Chirp Transducers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 6"W x 8"L WT: 0.1 lbs UPC: 801769003345

Read more less

Garmin 8-Pin Mix & Match Chirp Cable - 1MAirmar's 8-Pin Mix & Match Chirp Cable specifically for Garmin.Features: 8-Pin Length: 1M Chirp Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 6"W x 9"L WT: 0.1 lbs UPC: 801769003215

Read more less

Garmin 12-Pin Mix & Match Cable for Chirp TransducersAirmar's Garmin Mix & Match CableFeatures: 12-Pin Specifically for Chirp Transducers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 4"W x 4"L WT: 0.2 lbs UPC: 801769003239

Read more less

Airmar Standard Fairing Block for B45Model: 33-351-01B45 Standard Fairing Block.Dimensions: 4.25" x 2.37" x 1.87" Tall

Read more less

Mix & Match Cable for Raymarine 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: 600W For Raymarine 600W equipment

Read more less

MM-9N Mix & Match Cable for Simrad XSONIC Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: Connector: 9-pin, Depth only Fits: HDS Carbon, evo 3 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Furuno 10-Pin Mix & Match Cable for 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: 10-Pin For Furuno 10-Pin equipment

Read more less

MM-8G Mix & Match Cable for 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable.The short pigtail attached to the transducer ends in an Airmar 5-pin female connector. The adapter cables have a matching Airmar 5-pin male connector (shown below) at one end and the correct connector for a specific brand of electronics at the other end.Both parts are needed for installation. If the user changes equipment brand at some later time, the transducer can be left in place and the adapter cable replaced.Mix and Match 600W transducers include the B117, B45, B60, P319, P66*, P79, SS505, and SS60. (* not all models)A 12m (40') extension cable (part MM-5P-5P) is available with one male and one female 5-pin connector.Note that 600W Mix and Match cables cannot be used with 1kw transducers.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Airmar High Speed fairing Block with Hardware for B45Model: 33-509-01B45 High Speed Fairing Block and hardware (33-443-01).Dimensions: 13.75" x 2.56" x 2.94" TallWhat's in the Box: fairing block Hardware 33-443-01

Read more less

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS264 Specifications: Type: Tools Box Dimensions: 5"H x 6"W x 7"L WT: 1.1 lbs

Read more less

75WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 4"H x 5"W x 7"L WT: 0.85 lbs

Read more less

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS164 Specifications: Type: Tools Box Dimensions: 1"H x 6"W x 7"L WT: 0.95 lbs

Read more less

75WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench.For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 9"L WT: 0.65 lbs

Read more less

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 9"L WT: 0.55 lbs

Read more less

Airmar Single Arm WrenchModel: 164WR-2Single arm wrench for use with Airmar B164 and B175 series transducers

Read more less

Replacement speed insert for B744V and B66V housings.

Read more less

75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.55 lbs

Read more less

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench 60WR-2 or 60WR-3 for the hull nut.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 9"L WT: 0.5 lbs

Read more less

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: SS60 B60 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.5 lbs

Read more less

Airmar 10-Conductor In-Line Splice Model: D00342H Cable Gland Waterproof Connector Waterproof Rating IP67 Temp Range: -40C~-100C Material~Nylon Wire Range = 18AWG-22AWG This IP67 10-Conductor finally makes secure in-line cable splicing as easy as stripping cable and turning a screw The integrated cable gland provides strain relief and ensures a watertight connection. It’s solderless screw terminal connections allow field servicing of the splice without cutting or soldering. Ideal for use in exposed exterior or hostile environments such as engine room, bilge or sailboat mast applications. Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be connected, but many CHIRP fishfinders and sounders use brand-specific connectors.

Read more less

10-Conductor In-Line Cable Splice - IP67Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be connected, but many CHIRP fishfinders and sounders use brand-specific connectors.Gemeco has introduced a new line of in-line splices that can be used to connect CHIRP transducers to the correct connector for a given application. These splices are available in two models, one for wires with up to 6 conductors and one for wires with up to 10 conductors. Both models have waterproof gland fittings rated to IP67. A 1.3mm hex-head wrench is included. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Misc Box Dimensions: 1"H x 1"W x 5"L WT: 0.2 lbs

Read more less

Fits: newer style P66 transducers, Identifier: Horseshoe shaped slot in cover where cable exits. Older style P66 bracket (P/N 20-275-01) is no longer available

Read more less

Spares kit for S800 and ST800/ Contains all wearing parts in the paddlewheel and blankign plug. 1 - paddlewheel and shaft 2 - O-rings 1 - valve sleeve 1 - retaining ring Note: Not the same as ST600.

Read more less

Transom Mounting Bracket for P66 Transducer - 2004 & upThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 3"W x 4"L WT: 0.2 lbs UPC: 801769004656

Read more less

Thru-hull spares kit. Contains all wearing parts in the paddlewheel assembly Fits: Raymarine ST600, ST700 Contains: 1 paddlewheel and shaft 6 o-rings 1 valve 1 retaining ring

Read more less

Transom speed repair kit for S61 (can also use complete 33-105) and S63 transom paddlewheel speed sensors with cable Contains: 1 paddlewheel and shaft 2 yokes with shear pins (for S63,ST63 use only)

Read more less

Replacement bracket for P23 and P32 housing styles only.

Read more less

Airmar Connector Collar Kit for M&M Chirp TransducersModel: 33-292-04Replacement connector collar, retaining ring, o-ring and installation tool for all Airmar 12-pin Chirp Mix and Match transducer models.What's in the Box: Nut Split Wedge tool O-ring

Read more less