• Victron Galvanic Isolator VDI-16A, 16 AMP Max Waterproof Potted [GDI000016000] Victron Galvanic Isolator VDI-16A, 16 AMP Max Waterproof Potted [GDI000016000]

    Victron Energy Victron Galvanic Isolator VDI-16A, 16 AMP Max Waterproof Potted [GDI000016000]

    Galvanic Isolator VDI-16A, 16 AMP Max Waterproof PottedThe galvanic isolator prevents electrolytic corrosion. It blocks low-voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft, and so on.The galvanic isolator consists internally of two diodes which are connected in an anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc.The isolator is installed directly behind your boat's 120V - 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.Please contact your dealer for any returns, repairs or support issues related to this product. Owner's Manual (pdf)

    $109.65

  • Victron Skylla-IP65 24/35 3-Bank 120-240VAC Battery Charger [SKY024035100]

    Victron Energy Victron Skylla-IP65 24/35 3-Bank 120-240VAC Battery Charger [SKY024035100]

    Skylla-IP65 24/35 3-Bank 120-240VAC Battery ChargerA powerful, waterproof and intelligent battery charger with a 7-stage adaptive charge algorithm, suitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm.The wide range universal input voltage adds flexibility to the installation, the charger will maintain its full output power no matter where it is located in the world.The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air.Both models are available in two versions: 3 full rated outputs 1 full rated output together with an isolated 3A trickle charge output for a starter battery Models:12V/70A & 24V/35APlease contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charging Banks: 3 Charger Output Voltage: 24v Charger Output - Amps: 35a Charger Input - Voltage: 120/240v Box Dimensions: 10"H x 15"W x 19"L WT: 17.5 lbs UPC: 8719076051992 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    $836.40

  • Ancor 16-14 Female Heatshrink Snap Plug - 100-Pack [319899]

    Ancor Ancor 16-14 Female Heatshrink Snap Plug - 100-Pack [319899]

    16-14 Female Heatshrink Snap Plug - 100-PackFeatures: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC. Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief. Nylon insulator, preferred by experts, for Marine Grade resistance to sunlight, water, oil, chemicals, vibration and cut-through damage. UL Listed and CSA Recognized Highest shrink ratio - shrinks to 1/3 original size. Shrinks at 257 deg. F/125 deg. C. Operating temperature range 40 deg. C to 110 deg. C. ANCOR heat shrink connectors offer heat activated adhesive built into the sleeve of the heat shrink tubing Shrinks to form a water tight seal and the ultimate vibration and strain relief. Tinned for corrosion resistance. Pure copper for maximum current flow. Brazed seam for maximum strength. Wire Range: 16-14/.197 Size: 3-5mm/5mm Gender: Female Qty/Pkg: 100WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Snap Plugs Package Qty: 100 Heat Shrink: Yes Gauge: 16-14 AWG Box Dimensions: 1"H x 3"W x 8"L WT: 0.8 lbs UPC: 091887807714 Quick Guide (pdf)Brochure (pdf)

    $47.99

  • Blue Sea 4163 SS Push Button Switch - Off-(On) - Red - 10A [4163]

    Blue Sea Systems Blue Sea 4163 SS Push Button Switch - Off-(On) - Red - 10A [4163]

    4163 SS Push Button Switch - Off-(On) - Red - 10A 10A continuous Single Pole Double Throw or Single Pole Single Throw Can be wired for normally open or normally closed Installs with .110inch quick connects (included in retail package) Specifications Action: OFF-(ON) Amperage: 10A @ 12V DC Nominal Voltage: 12V DC Maximum LED Operating Current: 20mA Minimum Operating Temperature: -10° C Maximum Operating Temperature: 70° C Minimum Storage Temperature: -55° C Maximum Storage Temperature: 85° C Illumination: Independent – Separate contacts for LED power Mounting Hole: 19mm Switching Cycles: 18,000 Termination: 5 – 0.110inch Quick Connect terminals WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Stainless Action: (On)/Off Box Dimensions: 2"H x 3"W x 5"L WT: 0.1 lbs UPC: 632085041632

    $23.99

  • Sea-Dog Battery Terminal Wing Nut Style - Positive/Negative Set [415210-1]

    Sea-Dog Sea-Dog Battery Terminal Wing Nut Style - Positive/Negative Set [415210-1]

    Battery Terminal Wing Nut Style - Positive/Negative Set Wing Nut Style Battery Terminals convert battery posts to stud connectors and permit quick disconnection from the battery. Polarity specific to meet USCG regulations. Die cast lead construction. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    $11.99

  • Victron Lynx Smart BMS 500 Battery MGMT System f/Lithium Smart Batteries [LYN034160200] Victron Lynx Smart BMS 500 Battery MGMT System f/Lithium Smart Batteries [LYN034160200]

    Victron Energy Victron Lynx Smart BMS 500 Battery MGMT System f/Lithium Smart Batteries [LYN034160200]

    Lynx Smart BMS 500 Battery MGMT System for Lithium Smart BatteriesThe Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature-rich and complete option.Features: Built-in 500A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch Battery monitor, indicating the state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with our VictronConnect App, for setup and monitoring. Local and remote monitoring using a Victron GX device, for example, the Cerbo GX. The Lynx Smart BMS is part of the modular Lynx distribution system.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    $997.90

  • Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400] Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400]

    Victron Energy Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400]

    BatteryProtect BP-100 - 100AMP - 6-35 VDCFeatures: The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.  12/24V auto ranging The BatteryProtect automatically detects system voltage  Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.  Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    $53.55

  • Balmar Alternator 170 AMP 12V 3.15" Dual Foot Saddle K6 Pulley [XT-CR-170-K6]

    Balmar Balmar Alternator 170 AMP 12V 3.15" Dual Foot Saddle K6 Pulley [XT-CR-170-K6]

    Alternator 170 AMP 12V 3.15" Dual Foot Saddle K6 PulleyAlternator, XT Series, 170A, 12V, Saddle Mount (Dual Foot), 3.15in, K6 Serpentine Pulley, Case GroundHitachi-Style Mounting; Typical for Yanmar, Westerbeke, Lehman & Perkins-Sabre EnginesReplaces: AT-DF-165-12-IG, AT-DF-165-K6This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Amperage: 170A Voltage: 12v Box Dimensions: 9"H x 9"W x 10"L WT: 14 lbs Brochure (pdf)

    $981.99

  • Ancor Green 10 AWG Primary Cable - Sold By The Foot [1083-FT]

    Ancor Ancor Green 10 AWG Primary Cable - Sold By The Foot [1083-FT]

    Green 10 AWG Primary Cable - Sold By The FootFeatures: ANCOR Marine Grade™ wire is manufactured from tinned copper stranding for maximum protection against corrosion and electrolysis. Ultra flexible (Type 3) stranding resists fatigue due to vibration and flexing 10 AWG /5mm², UL 1426 Tinned Boat Cable WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Green Length (Feet): Sold By The Foot Gauge: 10 AWG Box Dimensions: 1"H x 1"W x 12"L WT: 0.1 lbs Quick Guide (pdf)

    $1.24

  • Blue Sea 7080 25 Amp Circuit Breaker Panel Mount 285 Series [7080]

    Blue Sea Systems Blue Sea 7080 25 Amp Circuit Breaker Panel Mount 285 Series [7080]

    285-Series Circuit Breaker Panel Mount - 25A Drop in replacement for 185-Series Circuit Breakers Visible reset lever shows open condition "Trip Free" - cannot be held closed after tripWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 25a Box Dimensions: 2"H x 5"W x 8"L WT: 0.3 lbs UPC: 632085170806 Brochure (pdf)

    $56.99

  • Mastervolt ChargeMaster Plus 24/20-3 Battery Charger [44320205] Mastervolt ChargeMaster Plus 24/20-3 Battery Charger [44320205]

    Mastervolt Mastervolt ChargeMaster Plus 24/20-3 Battery Charger [44320205]

    ChargeMaster Plus 24/20-3 Battery ChargerMake the most of your batteries with the ChargeMaster series, plugging in and charging anywhere in the world. Mastervolt’s ChargeMaster guarantees fast and complete charging of your batteries no matter where you are. Thanks to Mastervolt’s innovative 3-step+ charging process, batteries also perform better and last longer.All ChargeMasters can be easily connected to a MasterBus network with only one cable and one connection (with the exception of the ChargeMaster 12/10, ChargeMaster 12/15-2, and ChargeMaster 24/6). What’s more, you have the option for central, local, or remote monitoring, configuration, and control of your system.Clear DisplayA clearly lit display on the ChargeMaster provides all essential information: charge current, charge voltage, charge phase, and battery content measurement and/or battery condition measurement as a percentage of available Ah capacity. The display also provides an indication of MasterBus communication. Three buttons adjacent to the read-out panel allow for easy operating of the entire system. The ChargeMaster is available in various models to guarantee you the ideal battery charger for any situation and demand.Features: For recreational and semi-professional use. Suitable for any type of battery, including Lithium-Ion batteries. 3-Step+ charging technology for fast and complete charging also charges depleted batteries. Memory function prevents overcharging in case of unreliable mains. Safe and complete charging due to standard safety features. Charging capacity up to 1000 Ah battery banks. Easy to connect and quick to install. Can charge multiple battery banks simultaneously. Built-in system functionality (MasterBus) in combination with other Mastervolt products. Clear control panel (with the exception of the ChargeMaster 12/10, ChargeMaster 12/15-2, and ChargeMaster 24/6). Supplies your system without a battery. Charging your batteries with every voltageThe Mastervolt ChargeMaster supplies a maximum capacity wherever you are via auto-ranging. Auto-ranging ensures perfect fully automatic operation anywhere in the world, regardless of the available mains voltage (90-265 V AC, 50 or 60 Hz). The 3-step+ charging technology guarantees fast and complete charging, while the cos phi 1-regulation gets the most out of limited generator capacity.Robust Connections Solid metal-to-metal connectors equipped with strain relief prevent corrosion and overheating.Charging multiple battery banksThe ChargeMaster series has three equal charge outputs. Those of the smaller ChargeMaster models are pre-installed with two meters of cable for a plug & play solution, while the heavier models have one full output (for example for your service battery) and two outputs of 10 A, ideal for your starter batteries.DC Power SupplyEven if the batteries are not connected, Mastervolt ChargeMaster battery chargers can provide a constant DC output allowing you to turn on lights or keep the fridge cold.Specifications: Nominal output voltage: 24 V Total charge current: 20 A at 28.8 V Number of battery outlets: 3 Charge current second output: 20 A Charge current third output: 20 A Battery bank size: 40-200 Ah Nominal input voltage: 120/230 V (90-265 V), 50/60 Hz AC connection: Connector strips Power supply mode: Yes Galvanic isolation: Yes Display/read-out: LED display Specifications: Charger Input - Voltage: 120/230v Charger Output - Amps: 20a Charger Output Voltage: 24v Charging Banks: 3 Portable: No Box Dimensions: 6"H x 12"W x 16"L WT: 9 lbs UPC: 816882022890 Owner's Manual (pdf)

    $896.99

  • Blue Sea 7237 A-Series Double Pole Toggle - 30A - Black [7237]

    Blue Sea Systems Blue Sea 7237 A-Series Double Pole Toggle - 30A - Black [7237]

    A-Series Toggle Double PolePN: 7237Poles: 2Color: BlackAmperage: 30AFeatures: Meets American Boat and Yacht Council (ABYC) standards UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada The industry standard circuit breaker for Blue Sea Systems electrical panels Combines switching and circuit protection into a single device Used as AC Main circuit protection "Trip Free" design cannot be held "ON" during fault current condition WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 30a Box Dimensions: 2"H x 3"W x 5"L WT: 0.4 lbs UPC: 632085072377

    $46.99

  • BEP Emergency Parallel Switch - 12/24V - 500A [720-MDO-EP]

    BEP Marine BEP Emergency Parallel Switch - 12/24V - 500A [720-MDO-EP]

    Emergency Parallel Switch  - 12/24V - 500AThis Motorized Switch offers remotely activated, high current, emergency parallel connection suitable for emergency starting of large engines (up to 2500A for 10 seconds).  The emergency parallel functionality is conveniently operated via a momentary button on the dash, which when activated, will parallel the batteries for 10 minutes.  Once the 10 minutes has passed, the switch turns off, removing the risk of start batteries becoming flattened following a parallel switch being inadvertently left on.  Designed and constructed for the harsh marine environment, utilizing tinned copper conductors, stainless steel nuts, and high temperature, fiber reinforced plastics to ensure longevity.  The units are ignition protected, provide On/Off switching operation, and may be recessed or surface mounted. Features: 12/24 volt operation (both battery banks must be same voltage) Manual override option 10 minute remotely activated emergency parallel function (no voltage sensitive function) Technical Specifications: Volts - 12/24V Rating - 500A Dimensions (L x W x H) - 4" x 4" x 4.3" In the Box: Parallel Switch  Instruction manual *Sold as an Individual WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Lockable: No Positions: 2 Continuous Amperage: 500 Box Dimensions: 5"H x 5"W x 5"L WT: 2 lbs UPC: 843687004721 Owner's Manual (pdf)Brochure (pdf)

    $223.99

  • Victron Orion-TR Smart 24/12-30 30A (360W) Non-Isolated DC-DC or Power Supply [ORI241236140]

    Victron Energy Victron Orion-TR Smart 24/12-30 30A (360W) Non-Isolated DC-DC or Power Supply [ORI241236140]

    Orion-TR Smart 24/12-30 30A (360W) Non-Isolated DC-DC or Power SupplyThe Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch.The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.Suitable for high temperatures up to 55°C with a full rated output up to 40°C.VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 24v Charger Output - Amps: 30a Charger Output Voltage: 12v Box Dimensions: 4"H x 5"W x 8"L WT: 4.25 lbs UPC: 8719076048978 Quick Guide (pdf)Brochure (pdf)

    $215.05

  • Mastervolt MasterBus Cable - 1M [77040100]

    Mastervolt Mastervolt MasterBus Cable - 1M [77040100]

    MasterBus Cable - 1M Suitable for data traffic and powering peripheral equipment, this is the only cable you need for your MasterBus network. MasterBus compatible products come standard with two ports, while other equipment requires an interface.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    $35.99

  • Blue Sea 4001 Rotating Single Entry CableCap - Small Pair [4001]

    Blue Sea Systems Blue Sea 4001 Rotating Single Entry CableCap - Small Pair [4001]

    4001 Rotating Single Entry CableCap - Small Pair Features: Cable Size - All Pair - Red/Black Top rotates 360° to allow cable entry from any angle For batteries with integral marine wing nut posts WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    $6.99

  • Ancor Heavy Duty Lugs - 1/0 Gauge Wire - 5/16" Post - 25-Pack [242285]

    Ancor Ancor Heavy Duty Lugs - 1/0 Gauge Wire - 5/16" Post - 25-Pack [242285]

    Heavy Duty Lugs - 1/0 Gauge Wire - 5/16" Post - 25-PackCable Gauge: 1/0Screw Size: 5/16" ANCOR Marine Grade™ lugs are manufactured from heavy duty annealed tinned copper, providing for maximum current flow 100% tin plated copper resists corrosion from salt and moisture Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Lugs Post Size: 5/16" Package Qty: 25 Heat Shrink: No Gauge: 1/0 AWG Box Dimensions: 2"H x 2"W x 3"L WT: 1 lbs UPC: 091887246049 Quick Guide (pdf)

    $48.99

  • BEP Pro Installer ANL Through Panel Fuse Holder - 500A [778-ANLTP] BEP Pro Installer ANL Through Panel Fuse Holder - 500A [778-ANLTP]

    BEP Marine BEP Pro Installer ANL Through Panel Fuse Holder - 500A [778-ANLTP]

    ANL Through Panel Fuse Holder, 500AThis innovative, through-panel mounting fuse holder (Patent Pending) offers the user easy visual inspection of fuse state, and easy/safe access to change fuses if blown. It provides high-capacity fusing, fast response, high interrupt ratings (up to 3,000 Amps DC), and is ideal for protecting today's demanding onboard power electronics technology including inverters and battery chargers. It can also protect wiring from short circuits, for example as a main fuse to protect house circuits, protection for digital switching main feed circuits, or heavy duty loads. Convenient fuse inspection and replacement Compact footprint saves space Radiused connection points improve cable routing options (back-to-back lugs fit at any angle -90' to +90') Innovative clear cover provides insulation/protection Fuse viewing "window" in cover aids visual inspection of fuse state Label recess on cover allows fitting up to +" width (12.7mm) printed labels from handheld label printers Insert moulded studs offer superior mechanical strength Designed for the harsh marine environment Studs have anti-seize lubrication applied to prevent thread galling Cable connection studs: 10mm (3/8") Fuse mounting studs: 8mm (5/16"). Also allows 10mm (3/8") fuses to be used Fuse type: ANL or ANN (very fast acting) Amperage: 35-500A 50 VDC, or determined by fuse fitted (if lower) High temperature, fibre reinforced plastic base provides strength and chemical resistance Clear polycarbonate cover Tinned CDA260 highly conductive brass for improved strength on integral studs, stainless steel nuts and washers for longevity in the marine environment All threads are metric WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Fuse Type: ANL Type: Fuse Holders Box Dimensions: 2"H x 6"W x 7"L WT: 0.85 lbs UPC: 843687006824 Brochure (pdf)

    $70.99

  • Victron RJ12 UTP Cable - 10M [ASS030066100]

    Victron Energy Victron RJ12 UTP Cable - 10M [ASS030066100]

    RJ12 UTP Cable - 10MA cable to connect the BMV shunt to the BMV head unit. An RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    $25.50

  • Victron Busbar 600A 4P  Cover 4X 3/8" Plus 4X M8 Terminals [VBB160040010]

    Victron Energy Victron Busbar 600A 4P Cover 4X 3/8" Plus 4X M8 Terminals [VBB160040010]

    Busbar 600A 4P & Cover 4X 3/8" Plus 4X M8 TerminalsBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    $143.65

  • BEP Push Button Switch - 24V Latching On/Off - Blue LED [80-511-0007-01]

    BEP Marine BEP Push Button Switch - 24V Latching On/Off - Blue LED [80-511-0007-01]

    Push Button Switch - 24V Latching On/Off - Blue LEDPush-button Switches are built to last with their stainless steel components and silver alloy contacts. The through panel mount switches are ideal for lighting, switch, or dash panels, with colored rings that can be wired to either display power to the system or switch back lighting. The product line includes both switches and warning buzzers with LED light rings.Features: Maximum switch current rating 5 Amps IP67 environmental protection switches WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Blue Action: ON-OFF Box Dimensions: 1"H x 1"W x 2"L WT: 0.05 lbs UPC: 843687005513 Brochure (pdf)

    $40.99

  • Ancor Adhesive Lined Heat Shrink Tubing (ALT) - 1/4" x 3" - 3-Pack - Black [303103]

    Ancor Ancor Adhesive Lined Heat Shrink Tubing (ALT) - 1/4" x 3" - 3-Pack - Black [303103]

    Adhesive Lined Heat Shrink Tubing (ALT) - 1/4" x 3" - 3-Pack - BlackPackage of 3 Black 3"(7.6cm) long sections with a 1/4"(6.4mm) diameter that shrinks to 5/64"(2mm)Wire Range: 16-10 AWGFeatures: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257°F / 125°C Operating temperature range of -40°C to 110°C UL 224 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Heat Shrink Box Dimensions: 1"H x 2"W x 4"L WT: 0.05 lbs UPC: 091887302264

    $2.99

  • Ancor Brown 14AWG Tinned Copper Wire - 100' [104210]

    Ancor Ancor Brown 14AWG Tinned Copper Wire - 100' [104210]

    Brown 14AWG Tinned Copper Wire - 100'Ancor Marine Grade wire products are the longest lasting and most rugged available, exceeding UL 1426, ABYC and US Coast Guard Charter boat (CFR Title 46) standards. They are constructed with premium vinyl insulation that is rated at 600 volts, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. Highest quality ultra flexible (Type 3) tinned copper stranding provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Brown Length (Feet): 100' Gauge: 14 AWG Box Dimensions: 3"H x 4"W x 4"L WT: 2 lbs UPC: 091887105087 Quick Guide (pdf)Owner's Manual (pdf)

    $27.99

  • Victron Orion-TR DC-DC Converter - 24 VDC to 12 VDC - 20AMP Isolated [ORI241224110]

    Victron Energy Victron Orion-TR DC-DC Converter - 24 VDC to 12 VDC - 20AMP Isolated [ORI241224110]

    Orion-TR 24/12-20A (240W) Isolated DC-DC ConverterIsolated Model - separate in and out (-) leads Remote On/Off TerminalThe remote on/off terminal eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or for example the engine run/stop switch. All Models Are Short Circuit Proof and Can Be Paralleled to Increase Output CurrentAn unlimited number of units can be connected in parallel.  High Temperature Protected The output current will reduce at high ambient temperatures.  IP43 Protection When installed with the screw terminals oriented downward.  Screw Terminals No special tools are needed for installation.  Input Fuse (not replaceable) On 12 V and 24 V input models only.  Adjustable Output Voltage Not intended for battery charging (consider using an Orion-Tr Smart for battery charging).Specifications: Input Voltage Range: 16-35 V Under Voltage Shut Down: 14 V Under Voltage Restart: 15 V Nominal Output Voltage: 12.2 V Output Voltage Adjust Range: 10-15 V Output Voltage Tolerance: +/- 0,2 V Output Noise: 2 mV rms Cont. Output Current at Nominal Output Voltage and 40 Degrees C: 20 A Maximum Output Current (10 S) at Nominal Output Voltage: 25 A Short Circuit Output Current: 50 A Cont. Output Power at 25 Degrees C: 300 W Cont. Output Power at 40 Degrees C: 240 W Efficiency: 88 % No Load Input Current (2): < 100 mA  Current Consumption: < 200uA when disabled via its remote port Galvanic Isolation: 200 VDC between input, output, and case Operating Temperature Range: -20 to +55 Degrees C (derate 3 % per °C above 40 °C) Humidity: Max. 95 % non-condensing DC Connection: Screw terminals Maximum Cable Cross-Section: 16 mm² AWG6 Weight: 1.3 kg (3 lb) Dimensions (H x W x D): 130 x 186 x 70 mm (5.1 x 7.3 x 2.8 inch) Safety Standards: EN 60950 Immunity Standards: EN 61000-6-2, EN 61000-6-1, EN 55014-2 Automotive Directive Standards: ECE R10-5 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 24v Charger Output - Amps: 20a Charger Output Voltage: 12v Box Dimensions: 4"H x 5"W x 8"L WT: 2.9 lbs UPC: 8719076035251 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    $113.90

  • Ancor Standard Duplex Cable - Flat 16/2 AWG - 2 x 1mm2 Red/Black -Sold by the Foot [1217-FT]

    Ancor Ancor Standard Duplex Cable - Flat 16/2 AWG - 2 x 1mm2 Red/Black -Sold by the Foot [1217-FT]

    Standard Duplex Cable - Flat 16/2 AWG - 2 x 1mm² Red/Black -Sold by the FootAncor Marine Grade wire products are the longest lasting and most rugged available, exceeding UL 1426, ABYC and US Coast Guard Charter boat (CFR Title 46) standards. They are constructed with premium vinyl insulation that is rated at 600 Volts, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation. Highest quality ultra flexible (Type 3) tinned copper stranding provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. Specifications: Color: Red/Black Gauge: 16/2 AWG Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 12"L WT: 0.2 lbs

    $0.84

  • Pacer Green 18 AWG Primary Wire - 1,000  [WUL18GN-1000]

    Pacer Pacer Green 18 AWG Primary Wire - 1,000 [WUL18GN-1000]

    Green 18 AWG Primary Wire - 1,000' Pacer's marine wire is designed to handle the harshest marine environments.  It is manufactured to meet and exceed the most stringent specifications.  This 18 AWG marine wire is constructed in the USA to achieve the highest level of quality. Built from Type III class K tinned copper, this wire offers excellent flexibility.  The tinned copper also resists corrosion adding to the life of the wire.  What about the insulation?  After the copper is tinned it is then insulated with a durable and flexible PVC jacket.  The jacket makes this 18 AWG marine wire resistant to alkali, abrasion, acid, gas, oil, flame, and moisture.  What standards and compliances does this wire meet?  Pacer's marine wire exceeds the requirements and standards of UL, ABYC, and NMMA. Features: Built for durability, flexibility, and longevity in the harshest marine environments  So flexible that you can tie it into a knot without compromising any of its qualities  Proprietary insulation ensures the highest level of protection available  Ease of installation and the longevity of its design have helped solidify this marine wire as the choice of boating professionals Compliances: UL Standard - 1426 BC-5W2 U.S.C.G - 33 CFR part 183  ABYC - E-11.14  Technical Specifications: Conductor - Type III annealed finely stranded tinned copper ASTM B172 Class K Insulation -20 °C to 105 °C flexible, color-coded PVC Voltage Rating - 600-V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil and Moisture *Sold as an Individual Specifications: Color: Green Gauge: 18 AWG Length (Feet): 1,000' Box Dimensions: 7"H x 7"W x 7"L WT: 10.3 lbs UPC: 840248200974 Brochure (pdf)

    $114.99

  • Marinco 14/3 Lighted Extension Cord - Non-Locking - 15A - 25' [150025NL]

    Marinco Marinco 14/3 Lighted Extension Cord - Non-Locking - 15A - 25' [150025NL]

    14/3 Lighted Extension Cord - Non-Locking - 15A - 25'Marinco 15A extension cords feature marine-grade 14/3 SJTOW cable. The lighted female end provides visual power indication.Features: Clear ends with lighted female end for visual power indication 14/3 marine grade SJTOW cable ETL certified to UL standards WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 15a Length: 25' Type: Cordset Box Dimensions: 3"H x 6"W x 13"L WT: 2.5 lbs UPC: 093344062766

    $20.99

  • Balmar Alternator 100 AMP Kit 12V 1-2" Single Foot Spindle Mount J10 Pulley Regulator  Temp Sensor [621-VUP-MC-100-J10]

    Balmar Balmar Alternator 100 AMP Kit 12V 1-2" Single Foot Spindle Mount J10 Pulley Regulator Temp Sensor [621-VUP-MC-100-J10]

    Alternator 100 AMP Kit 12V 1-2" Single Foot Spindle Mount J10 Pulley Regulator & Temp SensorKit Includes: 621-100-J10 Alternator, MC-618 Regulator, Temperature Sensors, Mounting Hardware621-100-J10 Alternator: 100A, 12V, Spindle Mount (Single Foot), 1-2in, J10 AltMount Serpentine Pulley, Isolated Ground1" Motorola-Style Mounting;  Typical for Westerbeke, Lehman, Hino & Pathfinder Engines2" Delco-Style Mounting;  Typical for Volvo Penta (Gas & Diesel), John Deere, Perkins, Mercruiser, Pleasurecraft, Crusader, Indmar, Marine Power & other GM-based EnginesReplaces: 621-VUP-MC-100-SR-KITThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Amperage: 100A Voltage: 12v Box Dimensions: 10"H x 11"W x 14"L WT: 15.85 lbs UPC: 676205500722 Brochure (pdf)

    $965.99

  • Balmar Alternator 100 AMP 12V 1-2" Single Foot Spindle Mount J10 Pulley w/Isolated Ground [621-100-J10]

    Balmar Balmar Alternator 100 AMP 12V 1-2" Single Foot Spindle Mount J10 Pulley w/Isolated Ground [621-100-J10]

    Alternator 100 AMP 12V 1-2" Single Foot Spindle Mount J10 Pulley with Isolated GroundAlternator, 621 Series, 100A, 12V, Spindle Mount (Single Foot), 1-2in, J10 AltMount Serpentine Pulley, Isolated Ground 1" Motorola-Style Mounting;  Typical for Westerbeke, Lehman, Hino & Pathfinder Engines 2" Delco-Style Mounting;  Typical for Volvo Penta (Gas & Diesel), John Deere, Perkins, Mercruiser, Pleasurecraft, Crusader, Indmar, Marine Power & other GM-based EnginesReplaces: 621-100-SR-IGThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Amperage: 100A Voltage: 12v Box Dimensions: 9"H x 10"W x 10"L WT: 12.9 lbs UPC: 676205500685 Brochure (pdf)

    $717.99

  • Victron Inverter Remote On-Off Cable [ASS030550120]

    Victron Energy Victron Inverter Remote On-Off Cable [ASS030550120]

    Inverter Remote On-Off CableUse this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350, or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output:  VE.Bus BMS: the Inverter will be switched off when the batteries are empty BlueSolar MPPT Charger: connecting an inverter directly to the load output of a BlueSolar MPPT Charger is not possible; the inverter needs to be connected to the battery. Then use this cable to switch the inverter on and off with the load output. Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    $15.30

  • Victron Phoenix Inverter 24VDC - 1200VA - 120VAC - VE.Direct - NEMA 5-15R [PIN242122500]

    Victron Energy Victron Phoenix Inverter 24VDC - 1200VA - 120VAC - VE.Direct - NEMA 5-15R [PIN242122500]

    Phoenix Inverter 24VDC - 1200VA - 120VAC - VE.Direct - NEMA 5-15RPhoenix Inverter 24 VDC - 1200W - 120 VAC - 50/60Hz. Inverters allow you to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V, or 48VDC.The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring:In- and output voltage, % load, and alarmsPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    $331.50

  • Victron Smart BMS CL 12/100 f/Victron LIFEPO4 Batteries 12VDC Only [BMS110022000] Victron Smart BMS CL 12/100 f/Victron LIFEPO4 Batteries 12VDC Only [BMS110022000]

    Victron Energy Victron Smart BMS CL 12/100 f/Victron LIFEPO4 Batteries 12VDC Only [BMS110022000]

    Smart BMS CL 12/100 f/Victron LIFEPO4 Batteries 12VDC OnlyThe Smart BMS CL 12/100 is a Battery Management system for Victron lithium-iron-phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator.The BMS CL 12/100 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources, or DC loads in case of low battery voltage, high battery voltage, or over temperature.The dedicated alternator input provides current limiting and one-way traffic from the alternator into the battery, so any size alternator (and start battery) can be safely connected to the Smart Lithium battery or batteries.The BMS is also equipped with a remote on/off the connector, to turn the BMS (and the system) off via a remote switch, and a pre-alarm contact, to give a warning signal before the BMS will disconnect the batteries from the system.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    $166.60

  • Victron Indicator Eyelet (M8 Eyelet/30AMP ATO Fuse) f/Blue Smart IP65 Chargers [BPC900120114]

    Victron Energy Victron Indicator Eyelet (M8 Eyelet/30AMP ATO Fuse) f/Blue Smart IP65 Chargers [BPC900120114]

    Indicator Eyelet (M8 Eyelet/30AMP ATO Fuse) for Blue Smart IP65 ChargersThe Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers. 0.3m cable length 12 awg 20A max current Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Type: Ring Terminals Box Dimensions: 1"H x 5"W x 7"L WT: 0.25 lbs UPC: 8719076043065 Quick Guide (pdf)Brochure (pdf)

    $18.70

  • Victron Phoenix Inverter 24 VDC - 3000W - 120 VAC - 60Hz -VE.Bus [PIN243020100] Victron Phoenix Inverter 24 VDC - 3000W - 120 VAC - 60Hz -VE.Bus [PIN243020100]

    Victron Energy Victron Phoenix Inverter 24 VDC - 3000W - 120 VAC - 60Hz -VE.Bus [PIN243020100]

    Phoenix Inverter 24 VDC - 3000W - 120 VAC - 60Hz - VE. BusPure sine wave output, high peak power, and high efficiency. Combined high-frequency and line-frequency technologies ensure the best of both worlds.SinusMax - Superior EngineeringDeveloped for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromising on performance. Employing hybrid HF technology, the result is a top-quality product with compact dimensions, light in weight, and capable of supplying power, problem-free, to any load.Parallel & 3-phase Operation CapabilityUp to 6 Phoenix Inverters can operate in parallel to achieve higher power output. Six 24 V 5000 VA units, for example, will provide 24 kW / 30 kVA output power. Operation in a 3-phase configuration is also possible.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Waveform: Pure Sine Wave Outlet Qty: None Inverter Surge Rating: 6000w Inverter Output Voltage: 120v Inverter Input Voltage: 19-33v Inverter Cont. Output Wattage: 3000w GFCI: No DC Connection Type: Hardwire AC Connection Type: Hardwire Box Dimensions: 13"H x 13"W x 18"L WT: 47 lbs UPC: 8719076023739 Quick Guide (pdf)Brochure (pdf)

    $1,154.30

  • Ancor 12-10 AWG - 1/2" Nylon Ring Terminal - 25-Pack [210227]

    Ancor Ancor 12-10 AWG - 1/2" Nylon Ring Terminal - 25-Pack [210227]

    12-10 AWG - 1/2" Nylon Ring Terminal - 25-PackAncor's Marine Grade terminals differ from automotive terminals by being designed for the harsh marine environment. Nylon insulators are easy to crimp and will not split. Barrels are designed to tightly grip the wire with the least effort. Tinned copper gives the least electrical resistance but the most corrosion protection.Features: Nylon insulated with insulation grip Double crimp, funnel entry UL 486C WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Ring Terminals Post Size: 1/2" Package Qty: 25 Heat Shrink: No Gauge: 12-10 AWG Box Dimensions: 1"H x 3"W x 5"L WT: 0.2 lbs UPC: 091887212273 Brochure (pdf)

    $16.99

  • Ancor Adhesive Lined Heat Shrink Tubing - Assorted 8-Pack, 6", 20-2/0 AWG, Black [301506]

    Ancor Ancor Adhesive Lined Heat Shrink Tubing - Assorted 8-Pack, 6", 20-2/0 AWG, Black [301506]

    Adhesive Lined Heat Shrink Tubing - Assorted 8-Pack, 6", 20-2/0 AWG, BlackKit Includes:8 - Black heat shrink tubing sectionsFeatures: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257° F/125° C Operating temperature range of -40° C to 110° C UL 224 Color: Black WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Heat Shrink Box Dimensions: 1"H x 3"W x 8"L WT: 0.2 lbs UPC: 091887308051

    $13.99

  • SmartPlug Weather Door - Horizontal [RDPWL] SmartPlug Weather Door - Horizontal [RDPWL]

    SmartPlug SmartPlug Weather Door - Horizontal [RDPWL]

    Weather Door - Horizontal SmartPlug receptacles can be installed in industry standard outdoor electrical boxes when used in conjunction with our spring loaded weather doors.  SmartPlug plugs self-align with these receptacles and have an automatic lock system when engaged.  The push in design provides self cleaning for the pins and clips which insures clean power transfer.Compatible With:SmartPlug 30 and 50  AMP ReceptaclesFeatures: Weatherproof cover design Horizontal positioning  *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Parts Box Dimensions: 2"H x 5"W x 5"L WT: 0.3 lbs UPC: 682500440946 Brochure (pdf)

    $58.50

  • Blue Sea 1038 48V Dual USB Charger Contura Switch Mount [1038]

    Blue Sea Systems Blue Sea 1038 48V Dual USB Charger Contura Switch Mount [1038]

    1038 48V Dual USB Charger Contura Switch MountIntelligent device recognition maximizes charge rate for phones, tablets, or other mobile devices.Features: Ideal for golf carts and other 48V systems Spring-hinged lid keeps debris and moisture out Charges at the speed required by specific devices Internal filtering for reduced electronic interference Over temperature protection Conformal coated circuit board for the harsh marine environment Mounts in an existing contura switch aperture Specifications: Max Output Current: 4A DC (total) Input Voltage: 48V DC Input Voltage Range: 32-64V DC Reverse Polarity: Yes Short Circuit Protection: Yes Thermal Overload Protection: Yes USB: 2.0, Type A

    $52.99

  • Victron Skylla-IP65 12/70 3-Bank 120-240VAC Battery Charger [SKY012070100]

    Victron Energy Victron Skylla-IP65 12/70 3-Bank 120-240VAC Battery Charger [SKY012070100]

    Skylla-IP65 12/70 3-Bank 120-240VAC Battery ChargerA powerful, waterproof and intelligent battery charger with a 7-stage adaptive charge algorithm, suitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm.The wide range universal input voltage adds flexibility to the installation, the charger will maintain its full output power no matter where it is located in the world.The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air.Both models are available in two versions: 3 full rated outputs 1 full rated output together with an isolated 3A trickle charge output for a starter battery Models:12V/70A & 24V/35APlease contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charging Banks: 3 Charger Output Voltage: 12v Charger Output - Amps: 70a Charger Input - Voltage: 120/240v Box Dimensions: 10"H x 15"W x 19"L WT: 17.5 lbs UPC: 8719076051978 Quick Guide (pdf)Owner's Manual (pdf)

    $836.40

  • Ancor 12-10 Gauge - #10 Heat Shrink Ring Terminal - 3-Pack [312303]

    Ancor Ancor 12-10 Gauge - #10 Heat Shrink Ring Terminal - 3-Pack [312303]

    12-10 Gauge - #10 Heat Shrink Ring Terminal - 3-PackGauge Size: 12-10Screw Size: #10Quantity: 3Product Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Nylon insulator, preferred by experts, for Marine Grade™ resistance to sunlight, water, oil, chemicals, vibration and cut-through damage UL Listed and CSA Recognized Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257° F/125° C Operating temperature range 40° C to 110° C ANCOR heat shrink connectors offer heat activated adhesive built into the sleeve of the heat shrink tubing Shrinks to form a water tight seal and the ultimate vibration and strain relief Tinned for corrosion resistance Pure copper for maximum current flow Brazed seam for maximum strength WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Ring Terminals Post Size: #10 Package Qty: 3 Heat Shrink: Yes Gauge: 12-10 AWG Box Dimensions: 1"H x 1"W x 1"L WT: 0.1 lbs UPC: 091887316087 Quick Guide (pdf)

    $3.99

  • Ancor 22-18 Gauge - #8 Heat Shrink Ring Terminal - 3-Pack [310203]

    Ancor Ancor 22-18 Gauge - #8 Heat Shrink Ring Terminal - 3-Pack [310203]

    22-18 Gauge - #8 Heat Shrink Ring Terminal - 3-PackGauge Size: 22-18Screw Size: #8 Quantity: 3Product Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC. Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief. Nylon insulator, preferred by experts, for Marine Grade resistance to sunlight, water, oil, chemicals, vibration and cut-through damage. UL Listed and CSA Recognized Highest shrink ratio - shrinks to 1/3 original size. Shrinks at 257 deg. F/125 deg. C. Operating temperature range 40 deg. C to 110 deg. C. ANCOR heat shrink connectors offer heat activated adhesive built into the sleeve of the heat shrink tubing Shrinks to form a water tight seal and the ultimate vibration and strain relief. Tinned for corrosion resistance. Pure copper for maximum current flow. Brazed seam for maximum strength. Wire Range: 22-18 mm: 0.3-0.8 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Gauge: 22-18 AWG Type: Ring Terminals Post Size: #8 Package Qty: 3 Heat Shrink: Yes Box Dimensions: 1"H x 1"W x 1"L WT: 0.1 lbs UPC: 091887316261 Quick Guide (pdf)

    $2.99

  • Ancor Heavy Duty Lugs - 4/0 Gauge Wire - 1/2" Post - 10-Pack [242727]

    Ancor Ancor Heavy Duty Lugs - 4/0 Gauge Wire - 1/2" Post - 10-Pack [242727]

    Heavy Duty Lugs - 4/0 Gauge Wire - 1/2" Post - 10-PackCable Gauge: 4/0Screw Size: 1/2" ANCOR Marine Grade™ lugs are manufactured from heavy duty annealed tinned copper, providing for maximum current flow 100% tin plated copper resists corrosion from salt and moisture Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Package Qty: 10 Heat Shrink: No Type: Lugs Post Size: 1/2" Gauge: 4/0 AWG Box Dimensions: 2"H x 3"W x 4"L WT: 1 lbs UPC: 091887249040 Quick Guide (pdf)

    $39.99

  • Victron SmartShunt 2000A/50MV IP65 Bluetooth Battery Monitor [SHU065220050] Victron SmartShunt 2000A/50MV IP65 Bluetooth Battery Monitor [SHU065220050]

    Victron Energy Victron SmartShunt 2000A/50MV IP65 Bluetooth Battery Monitor [SHU065220050]

    SmartShunt 2000A/50MV IP65 Bluetooth Battery MonitorThe Smart Battery ShuntThe SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more.Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are wanted.The SmartShunt is equipped with Bluetooth and a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring, or a temperature sensor.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    $226.10

  • Blue Sea 8110 Mini Clamp Multimeter [8110]

    Blue Sea Systems Blue Sea 8110 Mini Clamp Multimeter [8110]

    Mini Clamp Multimeter Clamp allows measurement of AC and DC current in wires without disturbing the circuits or contacting live terminals Auto range simplifies operation: 0.01-400 Amps, 0.001-600 Volts Auto power-off selection - power turns off automatically after 10 minutes of non-use True RMS - required for accurate measurement of inverter output Large digital display makes reading measurements easy Data hold - press "HOLD" button during measurement to lock reading value Test leads included with meter WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

    $180.99

  • ARCO Marine Premium Replacement Inboard Alternator w/55mm Multi-Groove Pulley - 12V 65A [60073] ARCO Marine Premium Replacement Inboard Alternator w/55mm Multi-Groove Pulley - 12V 65A [60073]

    ARCO Marine ARCO Marine Premium Replacement Inboard Alternator w/55mm Multi-Groove Pulley - 12V 65A [60073]

    Premium Replacement Inboard Alternator with 55mm Multi-Groove Pulley - 12V 65AReplacement alternator that will fit Late model Volvo Penta, 12 Volt, 75 Amp, 50-mm multi-groove serpentine pulley included.Features: All alternators are engineered for performance and reliability All alternators are engineered and manufactured with precision and quality All alternators must meet or exceed OEM performance before being boxed Warranty Information:When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications. Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration Replaces:VOLVO Alternator 3862665VOLVO Alternator 3884950SIERRA Alternator 18-5882SIERRA Alternator 18-6845This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Amperage: 65A Voltage: 12v Box Dimensions: 8"H x 8"W x 9"L WT: 10.3 lbs UPC: 693006009544 Quick Guide (pdf)

    $222.99

  • Blue Sea 8275 Water Resistant Contura III Switch - ON-ON - Grey [8275]

    Blue Sea Systems Blue Sea 8275 Water Resistant Contura III Switch - ON-ON - Grey [8275]

    Water Resistant Contura Switch - ON-ON - GreyFeatures: Vibration, shock, thermoshock, moisture, and salt spray resistant Specially manufactured for mounting in Blue Sea Systems' water-resistant panels Ignition Protected - Safe for installation aboard gasoline-powered boats Meets UL1500 and ISO8846 ignition protection requirements WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Throw/Pole: DPDT Action: ON-ON Box Dimensions: 2"H x 3"W x 5"L WT: 0.2 lbs UPC: 632085082758

    $24.99

  • Blue Sea 7067 ATO/ATC-Style Low Profile Circuit Breaker - 2-Pack - 25 Amp [7067]

    Blue Sea Systems Blue Sea 7067 ATO/ATC-Style Low Profile Circuit Breaker - 2-Pack - 25 Amp [7067]

    7067 ATO/ATC-Style Low Profile Circuit Breaker - 2-Pack - 25 AmpUse a manually resettable circuit breaker instead of an ATO or ATC fuse.Features: Drop in replacement for ATO and ATC blade style fuses Manual push button reset complies with ABYC circuit protection requirements Compatible with Water-Resistant ST-Blade Fuse Block with cover secured Compatible with all other ST-Blade Fuse blocks without cover Amperage: 25 Amp Color: White Maximum Voltage: 28V DC Circuit Breaker Type: Thermal Trip, Manual Reset Interrupt Capacity: 2000A @ 28V DC Minimum Operating Temperature: -30° C Maximum Operating Temperature: 77° C WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 25a Box Dimensions: 1"H x 2"W x 4"L WT: 0.1 lbs UPC: 632085070670

    $9.99

  • Victron SmartSolar MPPT 250/60-TR Solar Charge Controller [SCC125060221]

    Victron Energy Victron SmartSolar MPPT 250/60-TR Solar Charge Controller [SCC125060221]

    SmartSolar MPPT 250/60-TR Solar Charge ControllerA solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulfated or otherwise damaged.MPPT: Ultra Fast Maximum Power Point TrackingBy constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.Remote Monitoring & ControlRemotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or another device via VictronConnect. If your installation is connected to the internet with a GX device, the Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both VictronConnect and VRM are free to use. For remote installations - even when there is no internet connection nearby - you may be able to monitor your MPPT by connecting the  GlobalLink 520.Load OutputThe intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    $435.20

Electrical
Footer image

© 2026 REBELLION MARINE, Powered by Shopify

    Login

    Forgot your password?

    Don't have an account yet?
    Create account