Flexible Door Catch Constructed of sturdy UV-resistant injection-molded nylon with a stainless steel spring clip. These Flexible Door Catches guarantee ease of alignment and durability in use. Includes a 304 stainless steel adjustable door strike. *Installs with two #4 RH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Smooth Quarter Turn Deck Plate - Black - 6" The Sea-Dog® Quarter-Turn Deck Plate is constructed of UV stabilized ABS. Features a new locking system that prevents over tightening, jamming, and cross threading. Easy to open and close. A specially engineered lubricated gasket is used in conjunction with a knife edge for a leak tested seal. Installs with six #8 FH fasteners (not included). Patent Pending. Avoid contact with acetone or strong solvents. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Stainless Steel Midget Vent - Medium Midget Vents provide a splash-proof opening through transoms, cabin sides, etc. Great for routing cables and wires or for covering thru-hull openings to shield water spray. Ideal for small lockers, they provide attractive cover for ventilation holes while also preventing odors. Corrosion resistant stamped 304 stainless steel construction. Easy to install with pre-drilled holes for three #6 RH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Combination Gas Fill & Tank Vent for 2" Hose - DieselFeatures: Chrome Plated Bronze Straight Neck Integral Tank Vent with Flame Arrestor O-Ring and Integral Retainer on Cap Included Ground Wire Required Specifications: For Fuel Hose: 2" For Vent Hose: 5/8" Length of Neck: 3-5/8" Screw Size: #8

Read more less

Cam BarThis cam bar is a spare part of Perko’s Flush Hatch Dog with a rectangular flange.  More specifically, it’s the cam bar for size #2. Quick Guide (pdf)

Read more less

Spare Bevel with CamThis is a spare part for Perko’s Mortise Latch Set. Specifications: Finish: Chrome Box Dimensions: 2"H x 2"W x 3"L WT: 0.1 lbs UPC: 085226052170

Read more less

Flush Pull Latch - Push To Close - Medium - BlackSpecifications: Material: Plastic Material Grade: PC / PBT Blend Finish: Natural Color/Appearance: Black Access Restriction: No Restriction Grip Range: 25.000-26.000 mm (0.98-1.02 in) Panel Thickness: 2.000-7.000 mm (0.08-0.28 in) Profile: Low Profile Size Series: Medium Size Southco offers modifications to our standard products, explore the possibilities of how Southco can engineer a solution to meet your specific application requirements.

Read more less

Spring Clamps 1" - 1-3/4" - PairFeatures: Stainless Steel Minimum I.D.: 1" Max I.D.: 1-3/4" Projection: 2-1/4" Width Clamp: 5/8"

Read more less

Teak Swim Platform with 3-Step Telescoping Ladder for Boats with Inboard/Outboard MotorsFeatures: 304 S.S. Hardware Platform Dimensions: 18"W (back) 17"W (front) x 15"D x 1-5/16" thick Includes Mounting Hardware Assembly required

Read more less

Locking Push Button LatchFeatures: Cut-Out: 1” Use for door/hatch where want to use forefinger and thumb to open Locking Great for glove boxes, electronic boxes, plexiglass doors

Read more less

20" Gas Spring - 40lb - Stainless SteelFeatures: 316 S.S. Gas Spring Ext. Length - 20" Comp. Length - 12" Rod Diamter - 5mm Tube Diameter - 15mm P1 Force - 40 Specifications: Lift Capacity: 40 lbs Length: 20" Box Dimensions: 1"H x 3"W x 22"L WT: 0.5 lbs UPC: 725060344078

Read more less

15" Gas Spring - 60lb - Stainless SteelFeatures: 316 S.S. Gas Spring Ext. Length - 15" Comp. Length - 9-1/2" Rod Dia. - 6mm Tube Dia. - 15mm P1 Force - 60 Specifications: Length: 15" Lift Capacity: 60 lbs Box Dimensions: 1"H x 1"W x 16"L WT: 0.35 lbs UPC: 725060336097

Read more less

15" Gas Spring - 20lb - Black NitrateFeatures: Black Nitride Gas Spring Ext. Length - 15" Comp. Length - 9-1/2" Rod Dia. - 6mm Tube Dia. - 15mm P1 Force - 20 Specifications: Length: 15" Lift Capacity: 20 lbs Box Dimensions: 1"H x 3"W x 17"L WT: 0.4 lbs UPC: 725060332051

Read more less

Surface Mount Flush Latch - Offset Cam Bar - 2.5" Hole - WhiteFeatures: White plastic and chrome plated zinc alloy Offset cam bar For surface thickness: 1/8" to 3/4" (0.3cm to 1.9cm) Face plate O.D.:3" (7.6cm) Installs in 2-1/2" (6.4cm) Diameter Hole

Read more less

Teak Louvered InsertHeight:9-3/8"Width:18"Depth:3/4"Cut OutHeight:8-3/8"Width:17"Measurements for the inserts, door, and drawer/door fronts are from outside edge to outside edge.All items have a 1/2" rabbet and use a cutout size one inch less than the listed dimension

Read more less

Long Towel Bar 23"L x 1"H x 2-1/2"D Includes mounting hardware

Read more less

Strap Hinge - PairLength:6"Width:1-1/8"Fastener:#10(6)Material: Polished Brass Specifications: Material: Brass Color: Brass Box Dimensions: 1"H x 3"W x 6"L WT: 0.4 lbs UPC: 725060060527

Read more less

Rectangular Drawer Pull 3-1/4" Length Recess Mount, 1/2" Deep 2-Pack

Read more less

Finger Pull 5/8" Barrel Length 1-1/4" Outer Diameter Recess Mount

Read more less

Fender CleatLength: 2"Base: 1-1/16" x 1-9/16"Fastener:#6(4)Material: Chrome Plated Brass Specifications: Finish: Polished Size: 2" Construction: Brass Box Dimensions: 1"H x 2"W x 2"L WT: 0.15 lbs UPC: 725060977030

Read more less

Teak Louvered InsertHeight:16"Width:9-1/8"Depth:3/4"Cut OutHeight:15"Width:8-1/8"Measurements for the inserts, door, and drawer/door fronts are from outside edge to outside edge.All items have a 1/2" rabbet and use a cutout size one inch less than the listed dimension

Read more less

Clam Shell Midget Vent 2-1/4" x 2-1/4" Material: 304 Stainless Steel Size: 2-1/4" x 2-1/4" Fastener: #6 (3)

Read more less

Command Ratchet Hinge - 18-1/2" - 316 Stainless Steel Polished with Hard StopBuilding upon the popularity of the H25-0023 heavy-duty Command Ratchet Hinge, this 18-1/2" hinge features a hard stop at 105º and is ideal for longer seat backs up to 22". This extended specialty hinge features one locking position at 62.5º and is perfect for sun pads, bolsters, and lounge backrests.Features & Benefits: Single- or double-seat capacity  Can be used for seat backs up to 22" long  Compatible with cushions up to 4" thick  Mounts above the deck  One locking position at 62.5º  Hard stop at 105°  Polished Type-304 stainless steel  Meets ABYC H-31 standards class B* application, 500 ft-lb. of torque load for a pair  500-hour salt fog test  Sold in pairs  Specifications: Length: 18-1/2" Width: 3" 5-year limited warranty

Read more less

Deck Fill for Pressure Relief Systems - Straight Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features: Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications) Automatic nozzle shutoff 4-18 gpm Stainless Steel finish An essential component of VaporTec and SecureStop Designed and tested to prevent water from entering the fuel system EPA / CARB Certified Hinged audible click cap meets EPA requirements Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less

Large Handle Kit - PairReplacement handle kit with both Left and Right-sided handles.Compatible With: Flush 3G hatch sizes 27, 30, 44, 60, 70, Bavaria big rectangle and Bavaria big square Coastline hatch, sizes 18, 22, 30, 40, 44, 50, 54, 60, 65 and 70 Ocean hatch, sizes 30, 40, 44, 50, 54, 60, 65, 66 (H.Rassy), 70, 75 and 77 Trimline hatch sizes 30, 40, 50, 60 and 70 Rolltop hatch, sizes 30, 40, 50, 60, 65 and 70 In the Box: One (1) Exterior Handle LH Grey Assembly One (1) Exterior Handle RH Grey Assembly Two (2) O-Ring Two (2) Exterior Handle - Grey Two (2) Base Bush - Grey Two (2) Base Bush O-ring Two (2) Handle packing washers One (1) Handle + Lock RH - Grey One (1) Handle + Lock LH - Grey Two (2) No. 10 Screw *Sold as an Individual

Read more less

Soft Grip 13" Steering WheelThis is the ideal steering wheel for bass boats, sport boats, and runabouts. The steering wheel has a patented design that provides a comfortable and firm grip. Also, this steering wheel has contemporary styling with a soft, black PVC outer rim and a high-impact, one-piece plastic inner core. It fits all standard 3/4-inch tapered shafts and conforms to ABYC P-22 and ISO 8848.Features: Resists UV rays to prevent fading Soft Grip is non-magnetic, so it will not interfere with compass readings 3-3/8 inch deep dish 8315 NMMA “As Approved”: 090071; CE Certificate WATT004 Specifications:Center Cap: Black plastic Specifications: Diameter (Inches): 13" Box Dimensions: 4"H x 14"W x 14"L WT: 2.75 lbs UPC: 022697831545 Quick Guide (pdf)

Read more less

316 Stainless Steel Alloy Flush Mount Fuel Vent - 90° VentOn the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets.Features:90-degree ventSpecifications: Hose Size (inch): 5/8" inner diameter Maximum Hull Thickness (inch): 7/8" Installation Hole Size (inch): 1-3/8" *Includes two silicone gaskets Quick Guide (pdf)

Read more less

Rigid Vinyl Flex-Core Rub Rail 1.58" x .635" - Frosty White 60'TACO Marine’s latest Rub Rail innovation is an improved design of our most popular rigid PVC shape with a lightweight, high-density inner core. This allows for easier handling, faster one-piece installation, improved dimensional stability, and production run consistency.Features: Ideal for boats up to 40 feet long Lightweight, easy handling and installation Solid, rigid PVC cap stock exhibits traditional surface characteristics, appearance, and impact properties Continuous coil eliminates butt joints around gunwale, with improved bending characteristics and the ability to cold form Vacuum calibration tooling allows for tighter dimensional tolerance and sizing consistency High-density core offers improved shock-absorbent impact resistance Made in the USA 5-year limited warranty Specifications: Color: Frosty white Length: (feet) 60' Insert: S11-4511 required (sold separately) Drilled and countersunk for #8 screw on 8-inch centers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Quick Release Fender LockStainless SteelHigh PolishFor dockside safety and convenience, Taco Marine's fender-clip ensures secure, quickly stored fender lines. The Fender clips ensure that lines remain at the optimum length with the mounting pin attached. At the dock, you simply insert the pin into the fitting and your boat is protected, with the fenders their ideal position.Features: Designed for simple single hand operation Will allow easy installation and removal of float style fenders Large push-button for comfortable operation Large hole diameter for rope Limited 3 year Warranty Material Characteristics Stainless Steel Type 316 Overall height above deck: 1.60° Drain plug: 1/4" NPT This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Brochure (pdf)

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Non-Skid Color: White

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: White

Read more less

Door Hinge - 1-1/2" x 3" - Investment Cast 316 Stainless SteelThese Door Hinges are constructed of corrosion-resistant investment-cast 316 stainless steel. Installs with six #10 FH fasteners (not included).Specifications:Fastener: #10 FH Specifications: Material: Stainless Steel Box Dimensions: 1"H x 2"W x 3"L WT: 0.2 lbs

Read more less

Elbow Catch This spring-loaded injection molded nylon Elbow Catch is ideal for the inactive side of a pair of cabinet doors. For use on wood or metal doors where no frame is present between doors. Surface mounted. These catches are quick and simple to install and allow for door to lock shut when pushed. Requires releasing the hook to open the door, making them very secure. Traditionally used in conjunction with a touch or magnetic latch on the primary door. Latch installs with two #6 FH fasteners. Slotted hole in catch allows for adjustable installation. Installation hardware not included.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Bow Eye - Machined 304 Stainless Steel - 7/16" x 3-1/2"These Bow Eyes are for use as a tie-down point on your boat’s bow. The 3/8" shafts have rolled threads. Constructed of corrosion-resistant machined 304 stainless steel. Includes adjustable finish nuts, which provide superior performance over crimp ring-style stern eyes. Can be used in conjunction with Lift Eyes (048330 or 048350) for a more robust lifting assembly.Specifications:Threads: 1/2" NC

Read more less

Cast Stainless Steel Handle/Latch - 3-3/4" x 3"The Hatch Handle Latches feature a handle that pivots out to open hatches and lays flush when not in use for a clean appearance. Ideal for use on doors, hatches, lazarettes, and dock boxes. Adjustable locking arm adds additional security. Once installed, the locking arm can be trimmed to length. Constructed of corrosion resistant investment cast 316 stainless steel. Installs with four #8 FH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Flush Hatch Pull Constructed of corrosion resistant investment cast 316 stainless steel. These hatch pulls are ideal for use on doors, hatches, lazarettes, and dock boxes. Handle pivots out to open hatches and lays flush when not in use for a clean appearance. Installs with four #8 FH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Gas Filled Lift Spring - 10" - 40# Sea-Dog® Gas Springs and hardware are manufactured to marine OE standards and have been installed in marine and RV applications for several years. You can count on our high quality and a 2-year warranty on all Sea-Dog® Gas Springs. Sea-Dog® Gas Springs are the ideal choice for all marine, RV, truck cap, tool box, and utility applications because of their unique multi-lobe seal which offers superior service life and performance. Hard chromium plated shafts, bronze bushings, and polymer end fittings mean you are buying THE BEST. Other applications for Sea-Dog® Gas Springs: Hatches, doors, tool boxes, farm machinery, golf carts, luggage doors, engine hatches, canopies, access hatches, seating, RV doors, furniture, truck caps, and utility boxes. Accepts 10 mm ball.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Length: 10" Lift Capacity: 40 lbs Box Dimensions: 1"H x 1"W x 11"L WT: 0.25 lbs UPC: 035514321785

Read more less

Smooth Quarter Turn Deck Plate - Black - 5" The Sea-Dog® Quarter-Turn Deck Plate is constructed of UV stabilized ABS. Features a new locking system that prevents over tightening, jamming, and cross threading. Easy to open and close. A specially engineered lubricated gasket is used in conjunction with a knife edge for a leak tested seal. Installs with six #8 FH fasteners (not included). Patent Pending. Avoid contact with acetone or strong solvents.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Anchor Replacement Roller - 2-3/4" x 2-7/8"Features: Nylon Replacement Wheel Diameter: 2-3/4" Width: 2-7/8" Rope Size: 3/4"

Read more less

Non-Locking Nylon T-Handle - White/WhiteWhitecap's Non-Locking White Nylon T-Handle.Specifications: Overall Dimensions: 3" Cut-Out - 2-1/2" Surface depth - 1/8" - 3/4" Fastener Included

Read more less

Teak Drinkholder with Removable Cockpit Table Top - Holds 4 GlassesFeatures: Table Top Dimensions: 16" x 24" Drinkholder holds four glasses Can be used without table Fits all 7/8" or 1" diameter tubing pedestal steering guards Easily removed

Read more less

Teak Six-Rod Storage Rack 22-1/2"L x 2-7/8"H x 3/4"D Sold in pairs

Read more less

PSS Shaft Seal 2-1/2" Shaft 4" TubeShaft Diameter: 2-1/2"Stern Tube Diameter (D): 4"Total Length (A): 9.625"Total Length (compressed) (Compressed A): 8.375"Rotor Diameter (B): 4.2"Carbon Cuff Diameter (C): 3.75"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

Grabber Catch Latch - Side Mount - Black - Pull-Up Force 22N (5lbf)Features: Spring-loaded over-center latching One assembly includes catch and keeper Material and Finish: PC/ABS, black Performance Details: Operating temperature range: -30ºC (-20ºF) to 60ºC (140ºF) Flammability rating: UL94-HB Installation Notes: Orient keeper to latch. The arrow on the keeper should point towards the cam. Mount to door and adjust for smooth latching. Minimum distance from frame (or surface on which catch subassembly is mounted) to centerline of door hinge is 150 (5.9)

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: White

Read more less

316 Stainless Steel Alloy Flush Mount Fuel Vent - Straight Vent On the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets.Features:Straight VentSpecifications: Hose Size (inch): 5/8" inner diameter Maximum Hull Thickness (inch): 7/8" Installation Hole Size (inch): 1-3/8" *Includes two silicone gaskets Quick Guide (pdf)

Read more less

90° P-Trap Fuel Tank Vent - Flush Mount - Black with Stainless Steel Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness. eliminates the need for an anti-siphon loop in the vent hose. This is a flush mount vent for use with a 5/8-inch interior diameter hose. It requires a 1-3/8-inch installation hole and can be used with a maximum hull thickness of 1 inch.Features: This black vent with a stainless steel vent head meets ABYC standards Flush Mount - 5/8" I.D. hose (inch) 1-3/8" install. hole size (inch) 1" Max. hull thickness *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less

Cowl VentilatorAttwood hull-mounted vents are designed to install by fastening as a complete unit from either inside or outside the hull. Ventilation hose (not included) twists into the bottom of the box to form a raised water barrier. Plastic vents are corrosion-resistant, will not discolor. All collector boxes and vents are designed for intake or exhaust and meet ABYC H-2 cross sectional area requirements.For use with 3" I.D. wire-supported ventilation hose. Features flexible hose flange that is screwed onto hose, then vent snaps onto the flange. Vent constructed of chrome-plated die-cast Perma-Plate® ZAMAK. Flange is non-corrosive plastic. Installs with #8 screws.Installation Hole Size: 3-1/4" to 3-1/2"WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less