Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

Lewmar 10LB LFX Anchoring Kit with 15 feet 5/16 G4 Chain 200 feet 5/8 in 8-Plait LineModel: 69600925Made from lightweight and strong

Read more less

Its unique shank profile and ballasted tip make the Delta anchor self-launching. The low centre of gravity and self-righting geometry ensure that the Delta anchor will set immediately. Consistent and reliable in performance, the Delta anchor has Lloyd's Register Type Approval as a High Holding Power anchor and is specified as the primary anchor used by numerous National Lifeboat organizations. Also available in premium grade Duplex/High Tensile stainless steel. All Delta anchors are "guaranteed for life against breakage". Lloyd's Test Certification is available for individual Delta anchors by arrangement. **Damage by deformation or bending is not covered by this guarantee.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 14.1 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 22 11/16 22 11/16 1 2 7/8 19 15/16 19 15/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 10.8 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 18 3/16 22 11/16 1 2 7/8 15 7/16 19 15/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Lewmar 21LB LFX Alloy FlukeAnchorModel: 0058110 High-grade anodized aluminum components Lightweight and strong holding power Quickly disassembles for stowage No welds Adjustable shank/fluke angle dependent on sea-bed Easily replaceable parts The new Lewmar LFX fluke anchor is constructed from High-grade anodized aluminum components delivering a lightweight, stylish anchor with a powerful holding power.The FLX Quickly disassembles for stowage as well as making parts easily replaceable. The FLX has an adjustable angled fluke for faster setting in sand or mud seabeds making it the ideal secondary anchor.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 10.6 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 17 5/8 22 11/16 1 2 7/8 14 13/16 19 15/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Lewmar Dual JoystickModel: 589267 Ergonomic control 'pad' gives tactile feedback Membrane switch panel sealed from dust and moisture ingress Single and dual controllers available Dual controllers give total control of vessel via multi-axis function pad 12-24V dual voltage supply Multi-function LED indicator displays system deployment, thruster operation, low voltage, motor temperature warnings & fault conditions. Upgrade kit allows installation of single or dual controllers into a thruster system with previous generation controllers Fit existing cut-out of Lewmar joysticks Removable cover Lewmar's new range of thruster controls provides a superior tactile control of single or dual thruster installations.The controllers are designed for all Lewmar TT, RT, SRT & VRT thrusters fitted with a blue box and can be fitted to thrusters fitted with a black-box using a controller adapter.The controllers are installed without the need for rear access and feature a snap-on bezel to neatly hide the mounting screws. A cover is also included, providing additional security against accidental use and giving extra environmental protection. If replacing a previous generation touch panel, joystick panel or dual joystick panel, the existing mounting hole and fixing screw positions can be reused.Specifications<table style='border-collapse: collapse' width='95%' border='1 feet>Range of controllers for Lewmar TT thruster range

Read more less

Lewmar VectorTM Manual Shallow Water Anchor - WhiteModel: 2024008752 Keeps your boat anchored securely in up to 8 ft. of water Quick, simple deployment with manual tensioning strap Effortless manual operation means no hoses, pumps, or wires Gas spring secured penetrating fiberglass spike for reliable positioning Corrosion-resistant powder-coated aluminum finish Versatile mounting options fit nearly any style of boat Lightweight design compatible with powerboats up to 22 ft. or 3,000 lbs. The Vector manual shallow water anchor by Lewmar provides precision positioning in up to 8 ft. of water. A gas spring secures the penetrating fiberglass spike, ensuring reliable and steadfast stability even through wake turbulence. Built with a corrosion-resistant powder-coated aluminum finish, this anchor withstands the elements season after season.What's in the Box: Vector Shallow Water Anchor white Mounting Hardware

Read more less

Lewmar VectorTM Manual Shallow Water Anchor - BlackModel: 2024008743 Keeps your boat anchored securely in up to 8 ft. of water Quick, simple deployment with manual tensioning strap Effortless manual operation means no hoses, pumps, or wires Gas spring secured penetrating fiberglass spike for reliable positioning Corrosion-resistant powder-coated aluminum finish Versatile mounting options fit nearly any style of boat Lightweight design compatible with powerboats up to 22 ft. or 3,000 lbs. The Vector manual shallow water anchor by Lewmar provides precision positioning in up to 8 ft. of water. A gas spring secures the penetrating fiberglass spike, ensuring reliable and steadfast stability even through wake turbulence. Built with a corrosion-resistant powder-coated aluminum finish, this anchor withstands the elements season after season.What's in the Box: Vector Shallow Water Anchor Black Mounting Hardware

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 10.6 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 20 3/16 20 3/16 1 2 7/8 17 3/8 17 3/8 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Both the 3-Button Windlass Remote Kit and the 5-Button Windlass & Thruster Kit are easily retrofitted to existing installations and include a replaceable battery. The fobs float and are waterproof to IP67 (1 Meter deep). Using over one billion individual codes, our proprietry encryption scheme prevents false triggering from any other device or similar fob. And both kits include a Receiver that supports up to eight remote key fobs (additional fobs sold separately). Allows wireless remote operation (up/Down) of any solenoid switched windlass. FCC & CE certified Kit includes one wireless fob and one receiver Notes: Most Lewmar products utilize solenoids although some of our smaller products may not. If in doubt contact your Lewmar representative.

Read more less

Lewmar's 3-strand rope is an economical choice for your windlass rode. Keep in mind, the windlass does not stow the rode in the anchor locker - gravity does. So make sure you have ample depth and volume in your anchor locker to accommodate the length of rode you have chosen. 3-Strand is typically 20-30% less expensive than premium plaited anchor line. 3-Strand line, when used in salt water, will stiffen over time. It can be soaked in a bucket of fresh water and fabric softener overnight (the longer the better) to bring back a more flexible condition. If this does not yield acceptable results, it should be replaced.

Read more less

Lewmar 66840045 Emergency Manual Recovery F/H2/3Model: 66840045Available on the H2/H3 as an optional extra, it remains fitted to the unit for user convenience.

Read more less

Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use (M6 / 1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA. Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) 1 in Flange Smoke Grey 6.04 3/8 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Hinge Length HX (in) Hinge Width HY (in) Cut-Out Length Flat X1 (in) Cut-Out Width Flat Y1 (in) Cut-Out Radii Flat R1 (in) 10 1.2 16 3.16 1 9/16 2 11/16 3/16 8 7/8 7 15/16 13 11/16 1 7/16

Read more less

Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use (M6 / 1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA. Flat base hatches cannot be used with Trim kits or Roller shades Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Flat Base Smoke Grey 5.77 3/8 Dimensions <table cellpadding="0 in style="border-collapse: collapse" border="1 in> Length X (in) Width Y (in) Height Z (in) Radii R (in) Hinge Length HX (in) Hinge Width HY (in) Cut-Out Length Flat X1 (in) Cut-Out Width Flat Y1 (in) Cut-Out Radii Flat R1 (in) 12 3/4 12 3/4 1 9/16 2 15/16 3/16 5 7/16 10 1/16 10 1/16 1 9/16

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 8.6 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 15 5/8 20 3/4 1 2 7/8 12 7/8 18 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Its unique shank profile and ballasted tip make the Delta anchor self-launching. The low centre of gravity and self-righting geometry ensure that the Delta anchor will set immediately. Consistent and reliable in performance, the Delta anchor has Lloyd's Register Type Approval as a High Holding Power anchor and is specified as the primary anchor used by numerous National Lifeboat organizations. Also available in premium grade Duplex/High Tensile stainless steel. All Delta anchors are "guaranteed for life against breakage". Lloyd's Test Certification is available for individual Delta anchors by arrangement. **Damage by deformation or bending is not covered by this guarantee.

Read more less

185mm x 6mm x 1500mm fiberglass tube for 185tt thrusters.

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

Lewmar's 3-strand rope is an economical choice for your windlass rode. Keep in mind, the windlass does not stow the rode in the anchor locker - gravity does. So make sure you have ample depth and volume in your anchor locker to accommodate the length of rode you have chosen. 3-Strand is typically 20-30% less expensive than premium plaited anchor line. 3-Strand line, when used in salt water, will stiffen over time. It can be soaked in a bucket of fresh water and fabric softener overnight (the longer the better) to bring back a more flexible condition. If this does not yield acceptable results, it should be replaced.

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 5.5 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 9 11/16 19 5/16 1 2 7/8 6 15/16 16 9/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Lewmar 14lb DTX Stainless Steel Anchor Model: 0057206 Manufactured from 316 stainless steel Self launching Ordinary Holding Power certified Guaranteed for 3 years against breakage The new DTX anchor fills the gap between the existing galvanised and stainless Delta(R) anchors, allowing boat owners and builders to specify a stainless steel anchor for a significantly reduced outlay. Made from 316 stainless steel, the DTX anchors feature exceptional anti-corrosional performance and the enhanced aesthetics that stainless anchors offer. Utilising lead ballast encapsulated within the tip of the anchor to achieve the perfect centre of gravity, the DTX offers the initial bite and holding reliability that users of our Delta(R) anchors have come to expect.

Read more less

Lewmar HM15H150PX Anchor Rode 15 feet 5/16 G4 Chain with 150 feet 5/8 in 8 Plait LineModel: HM15H150PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Both the 3-Button Windlass Remote Kit and the 5-Button Windlass & Thruster Kit are easily retrofitted to existing installations and include a replaceable battery. The fobs float and are waterproof to IP67 (1 Meter deep). Using over one billion individual codes, our proprietry encryption scheme prevents false triggering from any other device or similar fob. And both kits include a Receiver that supports up to eight remote key fobs (additional fobs sold separately). Allows wireless remote operation (up/Down) of any solenoid switched windlass. FCC & CE certified Kit includes one wireless fob and one receiver Notes: Most Lewmar products utilize solenoids although some of our smaller products may not. If in doubt contact your Lewmar representative.

Read more less

Lewmar 7LB LFX Anchoring Kitwith 10 feet G4 1/4 Chain 150 feet 1/2 in 8-Plait LineModel: 0058103Made from lightweight and strong

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

Lewmar's 3-strand rope is an economical choice for your windlass rode. Keep in mind, the windlass does not stow the rode in the anchor locker - gravity does. So make sure you have ample depth and volume in your anchor locker to accommodate the length of rode you have chosen. 3-Strand is typically 20-30% less expensive than premium plaited anchor line. 3-Strand line, when used in salt water, will stiffen over time. It can be soaked in a bucket of fresh water and fabric softener overnight (the longer the better) to bring back a more flexible condition. If this does not yield acceptable results, it should be replaced.

Read more less

Lewmar HM10H150PX Anchor Rode 10 feet 5/16 G4 Chain with 150 feet 5/8 in 8 Plait LineModel: HM10H150PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Lewmar LEWHM06HT150P Anchor Rode 6 feet 1/4 G4 Chain with 150 feet 1/2 in 8 Plait LineModel: HM06HT150P8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Its unique shank profile and ballasted tip make the Delta anchor self-launching. The low centre of gravity and self-righting geometry ensure that the Delta anchor will set immediately. Consistent and reliable in performance, the Delta anchor has Lloyd's Register Type Approval as a High Holding Power anchor and is specified as the primary anchor used by numerous National Lifeboat organizations. Also available in premium grade Duplex/High Tensile stainless steel. All Delta anchors are "guaranteed for life against breakage". Lloyd's Test Certification is available for individual Delta anchors by arrangement. **Damage by deformation or bending is not covered by this guarantee.

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 4.9 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 10 11/16 16 7/16 1 2 7/8 7 15/16 13 11/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Lewmar HM10HT125PX Anchor Rode 10 feet 1/4 G4 Chain with 125 feet 1/2 in 8 Plait LineModel: HM10HT125PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 4.9 5/16 Dimensions Length (in) Width (in) Height (in) Radii (in) Cut-Out Length (in) Cut-Out Width (in) Cut-Out Radii (in) 13 13 1 2 7/8 10 1/4 10 1/4 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

185mm x 6mm x 1000mm fiberglass tube for 185tt thrusters.

Read more less